Problema con lilo
Moderatore: Staff
Regole del forum
1) Citare sempre la versione di Slackware usata, la versione del Kernel e magari anche la versione della libreria coinvolta. Questi dati aiutano le persone che possono rispondere.
2) Per evitare confusione prego inserire in questo forum solo topic che riguardano appunto Slackware, se l'argomento è generale usate il forum Gnu/Linux in genere.
3) Leggere attentamente le risposte ricevute.
4) Scrivere i messaggi con il colore di default, evitare altri colori.
5) Scrivere in Italiano o in Inglese, se possibile grammaticalmente corretto, evitate stili di scrittura poco chiari, quindi nessuna abbreviazione tipo telegramma o scrittura stile SMS o CHAT.
6) Appena registrati è consigliato presentarsi nel forum dedicato.
La non osservanza delle regole porta a provvedimenti di vari tipo da parte dello staff, in particolare la non osservanza della regola 5 porta alla cancellazione del post e alla segnalazione dell'utente. In caso di recidività l'utente rischia il ban temporaneo.
1) Citare sempre la versione di Slackware usata, la versione del Kernel e magari anche la versione della libreria coinvolta. Questi dati aiutano le persone che possono rispondere.
2) Per evitare confusione prego inserire in questo forum solo topic che riguardano appunto Slackware, se l'argomento è generale usate il forum Gnu/Linux in genere.
3) Leggere attentamente le risposte ricevute.
4) Scrivere i messaggi con il colore di default, evitare altri colori.
5) Scrivere in Italiano o in Inglese, se possibile grammaticalmente corretto, evitate stili di scrittura poco chiari, quindi nessuna abbreviazione tipo telegramma o scrittura stile SMS o CHAT.
6) Appena registrati è consigliato presentarsi nel forum dedicato.
La non osservanza delle regole porta a provvedimenti di vari tipo da parte dello staff, in particolare la non osservanza della regola 5 porta alla cancellazione del post e alla segnalazione dell'utente. In caso di recidività l'utente rischia il ban temporaneo.
-
- Linux 2.x
- Messaggi: 407
- Iscritto il: sab 16 apr 2005, 0:00
- Località: Uno dei posti più belli d'Italia
Problema con lilo
Devo fare modifiche su lilo.conf ma non c'è verso di fargliele accettare, quando do # lilo -v
# lilo -v
LILO version 24.0 (released 07-Juni-2013)
* Copyright (C) 1992-1998 Werner Almesberger (until v20)
* Copyright (C) 1999-2007 John Coffman (until v22)
* Copyright (C) 2009-2013 Joachim Wiedorn (since v23)
This program comes with ABSOLUTELY NO WARRANTY. This is free software
distributed under the BSD License (3-clause). Details can be found in
the file COPYING, which is distributed with this software.
Compiled at 17:40:54 on Oct 27 2013
Warning: LBA32 addressing assumed
Reading boot sector from /dev/sda
Using BITMAP secondary loader
Calling map_insert_data
Mapping bitmap file /boot/slack.bmp
Calling map_insert_file
Boot other: /dev/sdb1, on /dev/sdb, loader CHAIN
Warning: Device 0x0810: Inconsistent partition table, 1st entry
CHS address in PT: 0:32:33 --> LBA (992)
LBA address in PT: 2048 --> CHS (0:68:9)
Fatal: Either FIX-TABLE or IGNORE-TABLE must be specified
If not sure, first try IGNORE-TABLE (-P ignore)
Sul pc c'è anche Windows installato.
# lilo -v
LILO version 24.0 (released 07-Juni-2013)
* Copyright (C) 1992-1998 Werner Almesberger (until v20)
* Copyright (C) 1999-2007 John Coffman (until v22)
* Copyright (C) 2009-2013 Joachim Wiedorn (since v23)
This program comes with ABSOLUTELY NO WARRANTY. This is free software
distributed under the BSD License (3-clause). Details can be found in
the file COPYING, which is distributed with this software.
Compiled at 17:40:54 on Oct 27 2013
Warning: LBA32 addressing assumed
Reading boot sector from /dev/sda
Using BITMAP secondary loader
Calling map_insert_data
Mapping bitmap file /boot/slack.bmp
Calling map_insert_file
Boot other: /dev/sdb1, on /dev/sdb, loader CHAIN
Warning: Device 0x0810: Inconsistent partition table, 1st entry
CHS address in PT: 0:32:33 --> LBA (992)
LBA address in PT: 2048 --> CHS (0:68:9)
Fatal: Either FIX-TABLE or IGNORE-TABLE must be specified
If not sure, first try IGNORE-TABLE (-P ignore)
Sul pc c'è anche Windows installato.
- lablinux
- Linux 4.x
- Messaggi: 1212
- Iscritto il: gio 27 nov 2008, 12:23
- Desktop: Gnome
- Distribuzione: Debian testing
- Località: Rho
Re: Problema con lilo
Dacci le partizioni e il file lilo.conf
Come dissero a me "non abbiamo la palla di cristallo"
Come dissero a me "non abbiamo la palla di cristallo"
-
- Linux 2.x
- Messaggi: 407
- Iscritto il: sab 16 apr 2005, 0:00
- Località: Uno dei posti più belli d'Italia
Re: Problema con lilo
Con cfdisk mi vede solo l'hd di slackware
Codice: Seleziona tutto
# fdisk -l
Disk /dev/sda: 80.0 GB, 80026361856 bytes
17 heads, 18 sectors/track, 510789 cylinders, total 156301488 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x000425b0
Device Boot Start End Blocks Id System
/dev/sda1 * 18 58593797 29296890 83 Linux
/dev/sda2 58593798 150390737 45898470 5 Extended
/dev/sda5 58593816 150390737 45898461 83 Linux
Disk /dev/sdb: 256.1 GB, 256060514304 bytes
255 heads, 63 sectors/track, 31130 cylinders, total 500118192 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x9f42c1bc
Device Boot Start End Blocks Id System
/dev/sdb1 * 2048 1026047 512000 7 HPFS/NTFS/exFAT
/dev/sdb2 1026048 500115455 249544704 7 HPFS/NTFS/exFAT
WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted.
Disk /dev/sdc: 320.1 GB, 320071851520 bytes
255 heads, 63 sectors/track, 38913 cylinders, total 625140335 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xdd3f1a8b
Device Boot Start End Blocks Id System
/dev/sdc1 2048 625139711 312568832 7 HPFS/NTFS/exFAT
bash-4.2#
Codice: Seleziona tutto
lilo.conf
# LILO configuration file
# generated by 'liloconfig'
#
# Start LILO global section
# Append any additional kernel parameters:
append=" vt.default_utf8=0"
boot = /dev/sda
#compact # faster, but won't work on all systems.
# Boot BMP Image.
# Bitmap in BMP format: 640x480x8
bitmap = /boot/slack.bmp
# Menu colors (foreground, background, shadow, highlighted
# foreground, highlighted background, highlighted shadow):
bmp-colors = 255,0,255,0,255,0
# Location of the option table: location x, location y, number of
# columns, lines per column (max 15), "spill" (this is how many
# entries must be in the first column before the next begins to
# be used. We don't specify it here, as there's just one column.
bmp-table = 60,6,1,16
# Timer location x, timer location y, foreground color,
# background color, shadow color.
bmp-timer = 65,27,0,255
# Standard menu.
# Or, you can comment out the bitmap menu above and
# use a boot message with the standard menu:
#message = /boot/boot_message.txt
# Wait until the timeout to boot (if commented out, boot the
# first entry immediately):
prompt
# Timeout before the first entry boots.
# This is given in tenths of a second, so 600 for every minute:
timeout = 600
# Override dangerous defaults that rewrite the partition table:
change-rules
reset
# Normal VGA console
vga = normal
# Ask for video mode at boot (time out to normal in 30s)
#vga = ask
# VESA framebuffer console @ 1024x768x64k
#vga=791
# VESA framebuffer console @ 1024x768x32k
#vga=790
# VESA framebuffer console @ 1024x768x256
#vga=773
# VESA framebuffer console @ 800x600x64k
#vga=788
# VESA framebuffer console @ 800x600x32k
#vga=787
# VESA framebuffer console @ 800x600x256
#vga=771
# VESA framebuffer console @ 640x480x64k
#vga=785
# VESA framebuffer console @ 640x480x32k
#vga=784
# VESA framebuffer console @ 640x480x256
#vga=769
# End LILO global section
# Windows bootable partition config begins
other = /dev/sdb1
label = Windows
table = /dev/sdb
# Windows bootable partition config ends
# Linux bootable partition config begins
image = /boot/vmlinuz
root = /dev/sda1
label = Linux
read-only
# Linux bootable partition config ends
Ultima modifica di conraid il mar 1 set 2015, 10:09, modificato 1 volta in totale.
Motivazione: Cerca di mettere le parti di codice o di file di configurazione racchiusi nel tag CODE.
Motivazione: Cerca di mettere le parti di codice o di file di configurazione racchiusi nel tag CODE.
- lablinux
- Linux 4.x
- Messaggi: 1212
- Iscritto il: gio 27 nov 2008, 12:23
- Desktop: Gnome
- Distribuzione: Debian testing
- Località: Rho
Re: Problema con lilo
a occhio e corce, sdb1 è la partizione di ripristino di windows. Prova con sdb2.
- brg
- Linux 3.x
- Messaggi: 580
- Iscritto il: sab 12 mar 2011, 14:20
- Slackware: 15.0
- Kernel: 5.15.117
- Desktop: KDE5
- Località: Montecatini
- Contatta:
Re: Problema con lilo
Non rispondo direttamente al problema segnalato, ma ricordo che lo sviluppo di LILO è prossimo a fermarsi e che su Slackware è disponibile anche GRUB.