Re: RAID1 non capisco.
Inviato: mar 19 feb 2013, 14:06
Occhio che se il tuo disco è SATA3 e l'adattatore supporta solo i dischi SATA-I, non ci fai nulla.
AAAARRRGGGGHHH!!!rik70 ha scritto:Occhio che se il tuo disco è SATA3 e l'adattore supporta solo i dischi SATA-I, non ci fai nulla.
troppo sgrammaticato io per accorgermi....rik70 ha scritto: L'urlo pensavo fosse per quello che ho scritto: l'adattore
Ops. scusa non avevo letto il tuo post.sunreal ha scritto: Come dicevo dietro ci sono le quattro coppie di piedini tipo master/slave, non sono quelle? .
Codice: Seleziona tutto
smartctl -a /dev/sdb
smartctl 6.0 2012-10-10 r3643 [i686-linux-3.2.29-smp] (local build)
Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF)
Device Model: WDC WD30EZRX-00DC0B0
Serial Number: WD-WMC1T0821026
LU WWN Device Id: 5 0014ee 003723c48
Firmware Version: 80.00A80
User Capacity: 3,000,592,982,016 bytes [3,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Feb 20 11:40:41 2013 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (42780) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 429) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x70b5) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 176 175 021 Pre-fail Always - 6175
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 182
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 121
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 139
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 10
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 174
194 Temperature_Celsius 0x0022 123 118 000 Old_age Always - 27
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 3
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 206 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 206 occurred at disk power-on lifetime: 115 hours (4 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 08 00:05:48.726 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 00:05:48.711 IDENTIFY DEVICE
ca 00 02 08 00 90 e0 08 00:05:48.155 WRITE DMA
ec 00 00 00 00 00 a0 08 00:05:48.125 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:05:48.106 SET FEATURES [Set transfer mode]
Error 205 occurred at disk power-on lifetime: 115 hours (4 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 08 00 90 e0 Device Fault; Error: ABRT at LBA = 0x00900008 = 9437192
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 02 08 00 90 e0 08 00:05:48.155 WRITE DMA
ec 00 00 00 00 00 a0 08 00:05:48.125 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:05:48.106 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 00:05:48.091 IDENTIFY DEVICE
ca 00 02 08 00 90 e0 08 00:05:47.535 WRITE DMA
Error 204 occurred at disk power-on lifetime: 115 hours (4 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 08 00:05:48.106 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 00:05:48.091 IDENTIFY DEVICE
ca 00 02 08 00 90 e0 08 00:05:47.535 WRITE DMA
ec 00 00 00 00 00 a0 08 00:05:47.506 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:05:47.487 SET FEATURES [Set transfer mode]
Error 203 occurred at disk power-on lifetime: 115 hours (4 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 08 00 90 e0 Device Fault; Error: ABRT at LBA = 0x00900008 = 9437192
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 02 08 00 90 e0 08 00:05:47.535 WRITE DMA
ec 00 00 00 00 00 a0 08 00:05:47.506 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:05:47.487 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 00:05:47.472 IDENTIFY DEVICE
ca 00 02 08 00 90 e0 08 00:05:46.916 WRITE DMA
Error 202 occurred at disk power-on lifetime: 115 hours (4 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 08 00:05:47.487 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 00:05:47.472 IDENTIFY DEVICE
ca 00 02 08 00 90 e0 08 00:05:46.916 WRITE DMA
ec 00 00 00 00 00 a0 08 00:05:46.886 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:05:46.867 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 116 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.