Inoltre dopo udev all'avvio mi dà dei strani uotput, ora posto un pò di tutto:
dmesg:
Codice: Seleziona tutto
Linux version 2.6.32-zen5-lupass7-06649-g632131e (root@archiso) (gcc version 4.4.2 20091208 (prerelease) (GCC) ) #1 ZEN SMP PREEMPT Sun Jan 17 13:58:53 CET 2010
Command line: root=/dev/sda3 ro
KERNEL supported cpus:
Intel GenuineIntel
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000004ffc0000 (usable)
BIOS-e820: 000000004ffc0000 - 000000004ffce000 (ACPI data)
BIOS-e820: 000000004ffce000 - 000000004fff0000 (ACPI NVS)
BIOS-e820: 000000004fff0000 - 0000000050000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
last_pfn = 0x4ffc0 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-DFFFF uncachable
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask FC0000000 write-back
1 base 040000000 mask FF0000000 write-back
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-000000004ffc0000
0000000000 - 004fe00000 page 2M
004fe00000 - 004ffc0000 page 4k
kernel direct mapping tables up to 4ffc0000 @ 8000-c000
ACPI: RSDP 00000000000fac00 00014 (v00 ACPIAM)
ACPI: RSDT 000000004ffc0000 00034 (v01 A M I OEMRSDT 09000508 MSFT 00000097)
ACPI: FACP 000000004ffc0200 00084 (v02 A M I OEMFACP 09000508 MSFT 00000097)
ACPI: DSDT 000000004ffc0440 049BB (v01 A0214 A0214001 00000001 INTL 02002026)
ACPI: FACS 000000004ffce000 00040
ACPI: APIC 000000004ffc0390 00068 (v01 A M I OEMAPIC 09000508 MSFT 00000097)
ACPI: MCFG 000000004ffc0400 0003C (v01 A M I OEMMCFG 09000508 MSFT 00000097)
ACPI: OEMB 000000004ffce040 00046 (v01 A M I AMI_OEM 09000508 MSFT 00000097)
ACPI: Local APIC address 0xfee00000
(5 early reservations) ==> bootmem [0000000000 - 004ffc0000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0001000000 - 000141db98] TEXT DATA BSS ==> [0001000000 - 000141db98]
#3 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#4 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
[ffffea0000000000-ffffea00011fffff] PMD -> [ffff880001a00000-ffff880002bfffff] on node 0
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x0004ffc0
On node 0 totalpages: 327519
DMA zone: 56 pages used for memmap
DMA zone: 101 pages reserved
DMA zone: 3842 pages, LIFO batch:0
DMA32 zone: 4424 pages used for memmap
DMA32 zone: 319096 pages, LIFO batch:31
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfecc0000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 3, address 0xfecc0000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 48
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 50000000 (gap: 50000000:aec00000)
NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 24 pages/cpu @ffff880001600000 s68888 r8192 d21224 u1048576
pcpu-alloc: s68888 r8192 d21224 u1048576 alloc=1*2097152
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 322938
Kernel command line: root=/dev/sda3 ro
PID hash table entries: 4096 (order: 3, 32768 bytes)
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Initializing CPU#0
Memory: 1283284k/1310464k available (2361k kernel code, 388k absent, 26068k reserved, 865k data, 292k init)
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:320
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration failed
TSC: Unable to calibrate against PIT
TSC: No reference (HPET/PMTIMER) available
Marking TSC unstable due to could not calculate TSC khz
Calibrating delay loop... 3948.54 BogoMIPS (lpj=1974272)
Security Framework initialized
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 4 MCE banks
CPU0: Thermal monitoring enabled (TM1)
using mwait in idle threads.
ACPI: Core revision 20090903
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay loop... 1998.84 BogoMIPS (lpj=999424)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU1: Thermal monitoring enabled (TM1)
CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03
Brought up 2 CPUs
Total of 2 processors activated (5947.39 BogoMIPS).
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: reg 10 32bit mmio pref: [0xf0000000-0xf7ffffff]
pci 0000:00:01.0: supports D1
pci 0000:00:0d.0: reg 10 32bit mmio: [0xfebc0000-0xfebdffff]
pci 0000:00:0d.0: reg 18 io port: [0xdc00-0xdc3f]
pci 0000:00:0d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:0d.0: PME# disabled
pci 0000:00:0f.0: reg 10 io port: [0xec00-0xec07]
pci 0000:00:0f.0: reg 14 io port: [0xe880-0xe883]
pci 0000:00:0f.0: reg 18 io port: [0xe800-0xe807]
pci 0000:00:0f.0: reg 1c io port: [0xe480-0xe483]
pci 0000:00:0f.0: reg 20 io port: [0xe400-0xe40f]
pci 0000:00:0f.0: reg 24 io port: [0xe000-0xe0ff]
pci 0000:00:0f.1: reg 20 io port: [0xfc00-0xfc0f]
pci 0000:00:10.0: reg 20 io port: [0xd880-0xd89f]
pci 0000:00:10.0: supports D1 D2
pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.0: PME# disabled
pci 0000:00:10.1: reg 20 io port: [0xd800-0xd81f]
pci 0000:00:10.1: supports D1 D2
pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.1: PME# disabled
pci 0000:00:10.2: reg 20 io port: [0xd480-0xd49f]
pci 0000:00:10.2: supports D1 D2
pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.2: PME# disabled
pci 0000:00:10.3: reg 20 io port: [0xd400-0xd41f]
pci 0000:00:10.3: supports D1 D2
pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.3: PME# disabled
pci 0000:00:10.4: reg 10 32bit mmio: [0xfebfb800-0xfebfb8ff]
pci 0000:00:10.4: supports D1 D2
pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.4: PME# disabled
pci 0000:00:11.5: reg 10 io port: [0xd000-0xd0ff]
pci 0000:00:11.5: supports D1 D2
pci 0000:01:00.0: reg 10 32bit mmio pref: [0xd0000000-0xd7ffffff]
pci 0000:01:00.0: reg 14 io port: [0xc800-0xc8ff]
pci 0000:01:00.0: reg 18 32bit mmio: [0xfeaf0000-0xfeafffff]
pci 0000:01:00.0: reg 30 32bit mmio pref: [0xfeac0000-0xfeadffff]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.1: reg 10 32bit mmio pref: [0xc8000000-0xcfffffff]
pci 0000:01:00.1: reg 14 32bit mmio: [0xfeae0000-0xfeaeffff]
pci 0000:01:00.1: supports D1 D2
pci 0000:00:01.0: bridge io port: [0xc000-0xcfff]
pci 0000:00:01.0: bridge 32bit mmio: [0xfea00000-0xfeafffff]
pci 0000:00:01.0: bridge 32bit mmio pref: [0xbff00000-0xdfefffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI Warning: Incorrect checksum in table [OEMB] - E8, should be DA (20090903/tbutils-314)
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
Switching to clocksource jiffies
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:07: ioport range 0x290-0x297 has been reserved
system 00:08: ioport range 0x3e0-0x3e7 has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x800-0x87f has been reserved
system 00:08: ioport range 0x400-0x41f has been reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0c: iomem range 0x0-0x9ffff could not be reserved
system 00:0c: iomem range 0xc0000-0xcffff has been reserved
system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
system 00:0c: iomem range 0x100000-0x4fffffff could not be reserved
system 00:0c: iomem range 0xfff80000-0xffffffff has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0xc000-0xcfff
pci 0000:00:01.0: MEM window: 0xfea00000-0xfeafffff
pci 0000:00:01.0: PREFETCH window: 0xbff00000-0xdfefffff
pci 0000:00:01.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io: [0xc000-0xcfff]
pci_bus 0000:01: resource 1 mem: [0xfea00000-0xfeafffff]
pci_bus 0000:01: resource 2 pref mem [0xbff00000-0xdfefffff]
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 2507
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler bfq registered (default)
Linux agpgart interface v0.103
sata_via 0000:00:0f.0: version 2.4
sata_via 0000:00:0f.0: PCI INT B -> GSI 20 (level, low) -> IRQ 20
sata_via 0000:00:0f.0: routed to hard irq line 10
scsi0 : sata_via
scsi1 : sata_via
ata1: SATA max UDMA/133 cmd 0xec00 ctl 0xe880 bmdma 0xe400 irq 20
ata2: SATA max UDMA/133 cmd 0xe800 ctl 0xe480 bmdma 0xe408 irq 20
pata_via 0000:00:0f.1: version 0.3.4
pata_via 0000:00:0f.1: PCI INT A -> GSI 20 (level, low) -> IRQ 20
scsi2 : pata_via
scsi3 : pata_via
ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
TCP cubic registered
NET: Registered protocol family 17
registered taskstats version 1
ata3.00: ATA-7: Maxtor 6E040L0, NAR61EA0, max UDMA/133
ata3.00: 80293248 sectors, multi 16: LBA
ata3.00: limited to UDMA/33 due to 40-wire cable
ata3.00: configured for UDMA/33
ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access ATA Maxtor 6E040L0 NAR6 PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 80293248 512-byte logical blocks: (41.1 GB/38.2 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 2:0:0:0: [sda] Attached SCSI disk
ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-4167B, DL10, max UDMA/33
ata4.00: configured for UDMA/33
scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-4167B DL10 PQ: 0 ANSI: 5
EXT2-fs: sda3: couldn't mount because of unsupported optional features (240).
EXT4-fs (sda3): mounted filesystem with ordered data mode
VFS: Mounted root (ext4 filesystem) readonly on device 8:3.
Freeing unused kernel memory: 292k freed
BFS CPU scheduler v0.313 by Con Kolivas.
Driver 'rtc_cmos' needs updating - please use bus_type methods
rtc_cmos 00:02: RTC can wake from S4
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 114 bytes nvram
udev: starting version 146
Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e1000 0000:00:0d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
e1000: 0000:00:0d.0: e1000_probe: (PCI:33MHz:32-bit) 00:13:d4:f0:71:cf
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
uhci_hcd: USB Universal Host Controller Interface driver
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
uhci_hcd 0000:00:10.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000d880
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.1: PCI INT A -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000d800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.2: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000d480
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.3: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000d400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
VIA 82xx Audio 0000:00:11.5: PCI INT C -> GSI 22 (level, low) -> IRQ 22
VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
usb 1-2: new full speed USB device using uhci_hcd and address 2
processor LNXCPU:00: registered as cooling_device0
processor LNXCPU:01: registered as cooling_device1
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 5 ports detected
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
usb 1-2.1: new low speed USB device using uhci_hcd and address 3
[drm] Initialized drm 1.1.0 20060810
usb 1-2.1: configuration #1 chosen from 1 choice
usb 1-2.3: new low speed USB device using uhci_hcd and address 4
[drm] radeon defaulting to kernel modesetting.
[drm] radeon kernel modesetting enabled.
radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[drm] radeon: Initializing kernel modesetting.
[drm] register mmio base: 0xFEAF0000
[drm] register mmio size: 65536
[drm] GPU reset succeed (RBBM_STATUS=0x00000140)
[drm] Generation 2 PCI interface, using max accessible memory
BUG: unable to handle kernel NULL pointer dereference at 0000000000000074
IP: [<ffffffffa01a8f17>] 0xffffffffa01a8f17
PGD 4c013067 PUD 4d470067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/module/snd_seq_oss/initstate
CPU 1
Modules linked in: radeon(+) ttm snd_seq_oss(+) snd_seq_midi_event snd_seq drm_kms_helper drm i2c_algo_bit i2c_core snd_pcm_oss snd_mixer_oss evdev processor thermal fan thermal_sys snd_via82xx uhci_hcd button snd_ac97_codec ac97_bus usbcore snd_pcm snd_timer snd_page_alloc battery snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore sr_mod cdrom e1000 ac rtc_cmos rtc_core rtc_lib
Pid: 1570, comm: modprobe Not tainted 2.6.32-zen5-lupass7-06649-g632131e #1
RIP: 0010:[<ffffffffa01a8f17>] [<ffffffffa01a8f17>] 0xffffffffa01a8f17
RSP: 0018:ffff88004ef83c58 EFLAGS: 00010292
RAX: 0000000000000000 RBX: ffff88004ed3b000 RCX: ffffffff81386be0
RDX: 0000000007ffffff RSI: ffff88004f91e800 RDI: ffff88004ef68800
RBP: ffff88004ef68800 R08: 00000000ffffffff R09: 00000000ffffffff
R10: 0000000000000000 R11: 0000000000000000 R12: ffff88004f91e800
R13: 0000000000000008 R14: ffffffffa01fe040 R15: ffff88004ef68b80
FS: 00007f33a3d49700(0000) GS:ffff880001700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000074 CR3: 000000004e071000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process modprobe (pid: 1570, threadinfo ffff88004ef82000, task ffff88004cecbe90)
Stack:
ffffffff00000008 ffff88004ef83cb8 ffff88004ef83c78 ffff88004ed3b000
<0> ffff88004ef68800 0000000000004000 ffffc900008a0000 0000000000004e20
<0> 0000000000000001 ffff88004ed3b000 ffff88004ef68800 ffff88004f91e800
Call Trace:
[<ffffffffa01c1ee5>] ? 0xffffffffa01c1ee5
[<ffffffffa01c8753>] ? 0xffffffffa01c8753
[<ffffffffa01a6305>] ? 0xffffffffa01a6305
[<ffffffffa01a6bc0>] ? 0xffffffffa01a6bc0
[<ffffffffa0144697>] ? 0xffffffffa0144697
[<ffffffff81143ed8>] ? 0xffffffff81143ed8
[<ffffffff81144836>] ? 0xffffffff81144836
[<ffffffff811a6ae5>] ? 0xffffffff811a6ae5
[<ffffffff811a6bc7>] ? 0xffffffff811a6bc7
[<ffffffff811a6d05>] ? 0xffffffff811a6d05
[<ffffffff811a6c8f>] ? 0xffffffff811a6c8f
[<ffffffff811a6488>] ? 0xffffffff811a6488
[<ffffffff811a5de7>] ? 0xffffffff811a5de7
[<ffffffff811a6f40>] ? 0xffffffff811a6f40
[<ffffffff81144a92>] ? 0xffffffff81144a92
[<ffffffffa0209000>] ? 0xffffffffa0209000
[<ffffffff81009027>] ? 0xffffffff81009027
[<ffffffff81050f11>] ? 0xffffffff81050f11
[<ffffffff8100b06b>] ? 0xffffffff8100b06b
Code: 74 85 c0 75 05 48 83 c4 08 c3 48 83 c4 08 e9 70 c6 f9 ff 41 55 41 54 55 53 48 83 ec 48 48 89 fb 48 8b 7f 08 48 8b 87 08 03 00 00 <8b> 50 74 85 d2 75 13 e8 d9 c5 f9 ff 89 c5 85 c0 0f 85 18 02 00
RIP [<ffffffffa01a8f17>] 0xffffffffa01a8f17
RSP <ffff88004ef83c58>
CR2: 0000000000000074
---[ end trace 7666bf4d7fe20518 ]---
usbcore: registered new interface driver hiddev
input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:10.0/usb1/1-2/1-2.1/1-2.1:1.0/input/input3
generic-usb 0003:046D:C016.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:10.0-2.1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usb 1-2.3: configuration #1 chosen from 1 choice
input: Chicony USB Keyboard as /devices/pci0000:00/0000:00:10.0/usb1/1-2/1-2.3/1-2.3:1.0/input/input4
generic-usb 0003:04F2:0403.0002: input,hidraw1: USB HID v1.11 Keyboard [Chicony USB Keyboard] on usb-0000:00:10.0-2.3/input0
input: Chicony USB Keyboard as /devices/pci0000:00/0000:00:10.0/usb1/1-2/1-2.3/1-2.3:1.1/input/input5
generic-usb 0003:04F2:0403.0003: input,hiddev0,hidraw2: USB HID v1.11 Device [Chicony USB Keyboard] on usb-0000:00:10.0-2.3/input1
Adding 987988k swap on /dev/sda2. Priority:-1 extents:1 across:987988k
e1000: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX Codice: Seleziona tutto
usbcore: registered new interface driver hiddev
input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:10.0/usb1/1-2/1-2.1/1-2.1:1.0/input/input3
generic-usb 0003:046D:C016.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:10.0-2.1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usb 1-2.3: configuration #1 chosen from 1 choice
input: Chicony USB Keyboard as /devices/pci0000:00/0000:00:10.0/usb1/1-2/1-2.3/1-2.3:1.0/input/input4
generic-usb 0003:04F2:0403.0002: input,hidraw1: USB HID v1.11 Keyboard [Chicony USB Keyboard] on usb-0000:00:10.0-2.3/input0
input: Chicony USB Keyboard as /devices/pci0000:00/0000:00:10.0/usb1/1-2/1-2.3/1-2.3:1.1/input/input5
generic-usb 0003:04F2:0403.0003: input,hiddev0,hidraw2: USB HID v1.11 Device [Chicony USB Keyboard] on usb-0000:00:10.0-2.3/input1
Adding 987988k swap on /dev/sda2. Priority:-1 extents:1 across:987988k
e1000: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
Codice: Seleziona tutto
Module Size Used by
usbhid 31552 0
hid 69376 1 usbhid
snd_seq_dummy 996 0
snd_seq_oss 19872 0
snd_seq_midi_event 3680 1 snd_seq_oss
snd_seq 34016 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
radeon 492128 1
ttm 27632 1 radeon
drm_kms_helper 19200 1 radeon
drm 113408 3 radeon,ttm,drm_kms_helper
i2c_algo_bit 4132 1 radeon
i2c_core 13448 3 radeon,drm,i2c_algo_bit
snd_pcm_oss 29504 0
snd_mixer_oss 11424 1 snd_pcm_oss
evdev 6624 0
thermal 9696 0
processor 19348 0
fan 2016 0
thermal_sys 9728 3 thermal,processor,fan
button 3720 0
snd_via82xx 15588 0
snd_ac97_codec 90424 1 snd_via82xx
ac97_bus 768 1 snd_ac97_codec
snd_pcm 45096 3 snd_pcm_oss,snd_via82xx,snd_ac97_codec
snd_timer 13872 2 snd_seq,snd_pcm
uhci_hcd 17280 0
snd_page_alloc 5200 2 snd_via82xx,snd_pcm
battery 4128 0
usbcore 100044 2 usbhid,uhci_hcd
snd_mpu401_uart 3776 1 snd_via82xx
snd_rawmidi 13184 1 snd_mpu401_uart
snd_seq_device 3636 4 snd_seq_dummy,snd_seq_oss,snd_seq,snd_rawmidi
snd 37192 11 snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_via82xx,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 4416 1 snd
e1000 84996 0
sr_mod 10500 0
cdrom 29864 1 sr_mod
ac 1664 0
rtc_cmos 6748 0
rtc_core 10532 1 rtc_cmos
rtc_lib 1728 1 rtc_core
Vi allego anche il config del kernel se magari vi può essere d'aiuto per aiutarmi
Grazie in anticipo per gli aiuti!
CIao Ciao!
