slacky.eu


https://slacky.eu/forum/

[RISOLTO] Vodafone UMTS card

https://slacky.eu/forum/viewtopic.php?f=1&t=11338

Pagina 1 di 1

[RISOLTO] Vodafone UMTS card

Inviato: ven 10 feb 2006, 19:00
da desmo
Ciao a tutti! Non riesco ad installare la connect card Vodafone UMTS e non riesco a trovare delle info utili....
Ho come l'impressione di sbagliare qualche cosa nella compilazione del kernel.

Dopo aver smanettato un po con il kernel sono riuscito ad abilitare la PCMCIA, almeno lampeggia :?

Quando inserisco la scheda pero nel /var/log/messages non mi rileva nulla :cry:

Facendo lspci:
root@desmo:/dev/usb# lspci
00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 03)
00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03)
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10]
02:06.0 CardBus bridge: O2 Micro, Inc. OZ711M3/MC3 4-in-1 MemoryCardBus Controller
02:06.1 CardBus bridge: O2 Micro, Inc. OZ711M3/MC3 4-in-1 MemoryCardBus Controller
02:06.2 System peripheral: O2 Micro, Inc. OZ711Mx 4-in-1 MemoryCardBus Accelerator
02:06.3 CardBus bridge: O2 Micro, Inc. OZ711M3/MC3 4-in-1 MemoryCardBus Controller
02:0d.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
02:0e.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5705M_2 Gigabit Ethernet (rev 03)
07:00.0 USB Controller: OPTi Inc. 82C861 (rev 10)
Il pacchetto pcmcia-cd e' installato.......

Ecco il config...

<*> PCCard (PCMCIA/CardBus) support
[*] Enable PCCARD debugging
<*> 16-bit PCMCIA support
[*] Load CIS updates from userspace (EXPERIMENTAL)
[*] PCMCIA control ioctl (obsolete)
--- 32-bit CardBus support
--- PC-card bridges
<M> CardBus yenta-compatible bridge support
<M> Cirrus PD6729 compatible bridge support
<M> i82092 compatible bridge support
<M> i82365 compatible bridge support
<M> Databook TCIC host bridge support
Se faccio il restart di /etc/rc.d/rc.pcmcia nel message logga questo:

Feb 10 18:54:55 desmo cardmgr[4436]: watching 3 sockets
Feb 10 18:54:55 desmo kernel: cs: IO port probe 0xc00-0xcff: clean.
Feb 10 18:54:55 desmo last message repeated 2 times
Feb 10 18:54:55 desmo kernel: cs: IO port probe 0x820-0x8ff: clean.
Feb 10 18:54:55 desmo last message repeated 2 times
Feb 10 18:54:55 desmo kernel: cs: IO port probe 0x800-0x80f: clean.
Feb 10 18:54:55 desmo last message repeated 2 times
Feb 10 18:54:55 desmo kernel: cs: IO port probe 0x3e0-0x4ff: clean.
Feb 10 18:54:55 desmo last message repeated 2 times
Feb 10 18:54:55 desmo kernel: cs: IO port probe 0x100-0x3af: excluding 0x140-0x14f 0x170-0x177 0x370-0x37f
Feb 10 18:54:55 desmo last message repeated 2 times
Feb 10 18:54:55 desmo kernel: cs: IO port probe 0xa00-0xaff: clean.
...ragazzi non so piu come fare. Avete un suggerimento?
Il kernel e' 2.6.14

Inviato: sab 11 feb 2006, 8:47
da l1q1d
supponendo che sia un modem guarda online se esistono delle specifiche...

Inviato: mer 13 dic 2006, 16:54
da desmo
La situazione e' questa:
Slackware 11
Kernel 2.6.18

Avvio tutto senza la connect card inserita e in /var/log/messag mi traccia:

Codice: Seleziona tutto

Dec 13 16:12:38 omht171p kernel: pccard: CardBus card inserted into slot 1
Dec 13 16:12:38 omht171p kernel: ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [C0C4] -> GSI 10 (level, low) -> IRQ 10
Dec 13 16:12:38 omht171p kernel: ohci_hcd 0000:05:00.0: OHCI Host Controller
Dec 13 16:12:38 omht171p kernel: ohci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 5
Dec 13 16:12:38 omht171p kernel: ohci_hcd 0000:05:00.0: irq 10, io mem 0x3a000000
Dec 13 16:12:38 omht171p kernel: usb usb5: configuration #1 chosen from 1 choice
Dec 13 16:12:38 omht171p kernel: hub 5-0:1.0: USB hub found
Dec 13 16:12:38 omht171p kernel: hub 5-0:1.0: 2 ports detected
Dec 13 16:12:44 omht171p kernel: ohci_hcd 0000:05:00.0: wakeup
Dec 13 16:12:45 omht171p kernel: usb 5-1: new full speed USB device using ohci_hcd and address 2
Dec 13 16:12:45 omht171p kernel: usb 5-1: configuration #1 chosen from 1 choice
Eseguo;

Codice: Seleziona tutto

modprobe usbserial vendor=0xaf0 product=0x5000
In /var/log/messag traccia:

Codice: Seleziona tutto

Dec 13 16:12:44 omht171p kernel: ohci_hcd 0000:05:00.0: wakeup
Dec 13 16:12:45 omht171p kernel: usb 5-1: new full speed USB device using ohci_hcd and address 2
Dec 13 16:12:45 omht171p kernel: usb 5-1: configuration #1 chosen from 1 choice
Dec 13 16:13:48 omht171p kernel: usbcore: registered new driver usbserial
Dec 13 16:13:48 omht171p kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
Dec 13 16:13:48 omht171p kernel: usbserial_generic 5-1:1.0: generic converter detected
Dec 13 16:13:48 omht171p kernel: usb 5-1: generic converter now attached to ttyUSB0
Dec 13 16:13:48 omht171p kernel: usbserial_generic 5-1:1.1: generic converter detected
Dec 13 16:13:48 omht171p kernel: usb 5-1: generic converter now attached to ttyUSB1
Dec 13 16:13:48 omht171p kernel: usbserial_generic 5-1:1.2: generic converter detected
Dec 13 16:13:48 omht171p kernel: usb 5-1: generic converter now attached to ttyUSB2
Dec 13 16:13:48 omht171p kernel: usbcore: registered new driver usbserial_generic
Dec 13 16:13:48 omht171p kernel: drivers/usb/serial/usb-serial.c: USB Serial Driver core
Il bello di tutto questo e' che in

Codice: Seleziona tutto

 /dev
non ho alcun

Codice: Seleziona tutto

ttyUSB0 o ttyUSB1 o ttyUSB2
La scheda blinca correttamente.

Lanciando lsusb -v la vedo correttamente.
Avete idea dove sbglio? Eppure in precedenza con la 10.2 di Slackware e altri kernel problemi ZERO. Puo essere qualche modulo? Ho fatto riferimento alle solite guide, piu o meno tutte uguali.....

By!

Inviato: mer 13 dic 2006, 21:03
da l1q1d
la device si trova in /dev/tty/USB0 se non sbaglio..

Inviato: mar 19 dic 2006, 9:14
da desmo
Eccoli....

Codice: Seleziona tutto

root@omht171p:/dev/tts# ls -la
total 0
drwxr-xr-x  2 root root     180 2006-12-19 09:12 .
drwxr-xr-x 19 root root   14680 2006-12-19 09:12 ..
crw-rw----  1 root tty    4, 64 2006-12-19 09:42 0
crw-rw----  1 root tty    4, 65 2006-12-19 09:42 1
crw-rw----  1 root tty    4, 66 2006-12-19 09:42 2
crw-rw----  1 root tty    4, 67 2006-12-19 09:42 3
crw-rw----  1 root tty  188,  0 2006-12-19 09:12 USB0
crw-rw----  1 root tty  188,  1 2006-12-19 09:12 USB1
crw-rw----  1 root tty  188,  2 2006-12-19 09:12 USB2
Tutti gli orari sono UTC+02:00
Pagina 1 di 1

Creato da phpBB® Forum Software © phpBB Limited

Traduzione Italiana phpBB-Store.it