Codice: Seleziona tutto
Linux version 2.6.16.22 (root@takezo) (gcc version 3.4.4) #1 SMP PREEMPT Tue Jun 27 17:16:04 CEST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffd0000 (usable)
BIOS-e820: 000000003ffd0000 - 000000003ffde000 (ACPI data)
BIOS-e820: 000000003ffde000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 262096
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32720 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f79b0
ACPI: RSDT (v001 A M I OEMRSDT 0x01000627 MSFT 0x00000097) @ 0x3ffd0000
ACPI: FADT (v002 A M I OEMFACP 0x01000627 MSFT 0x00000097) @ 0x3ffd0200
ACPI: MADT (v001 A M I OEMAPIC 0x01000627 MSFT 0x00000097) @ 0x3ffd0390
ACPI: MCFG (v001 A M I OEMMCFG 0x01000627 MSFT 0x00000097) @ 0x3ffd03f0
ACPI: BOOT (v001 A M I OEMBOOT 0x01000627 MSFT 0x00000097) @ 0x3ffd0430
ACPI: OEMB (v001 A M I AMI_OEM 0x01000627 MSFT 0x00000097) @ 0x3ffde040
ACPI: DSDT (v001 A6JC0 A6JC0206 0x00000206 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:14 APIC version 20
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bee00000)
Built 1 zonelists
Kernel command line: BOOT_IMAGE=slack ro root=308 resume=/dev/hda7 pci=assign-busses pci=routeirq
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1833.959 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034984k/1048384k available (2384k kernel code, 12768k reserved, 764k data, 220k init, 130880k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3673.28 BogoMIPS (lpj=1836641)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000140 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
tbxface-0109 [02] load_tables : ACPI Tables successfully acquired
Parsing all Control Methods:
Table [DSDT](id 0005) - 1157 Objects with 67 Devices 382 Methods 36 Regions
ACPI Namespace successfully loaded at root c04727b0
evxfevnt-0091 [03] enable : Transition to ACPI mode successful
CPU0: Intel Genuine Intel(R) CPU T2400 @ 1.83GHz stepping 08
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3666.44 BogoMIPS (lpj=1833220)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000140 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU T2400 @ 1.83GHz stepping 08
Total of 2 processors activated (7339.72 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=1000
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
PCI: Using MMCONFIG
ACPI: Subsystem revision 20060127
evgpeblk-0941 [06] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
evgpeblk-1037 [05] ev_initialize_gpe_bloc: Found 6 Wake, Enabled 4 Runtime GPEs in this block
Completing Region/Field/Buffer/Package initialization:............................................................................................................................
Initialized 35/36 Regions 17/17 Fields 33/33 Buffers 39/40 Packages (1166 nodes)
Executing all Device _STA and_INI methods:........................................................................
72 Devices found - executed 0 _STA, 4 _INI methods
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: Embedded Controller [EC0] (gpe 28) interrupt mode.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 7 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 *6 7 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 12)
ACPI: Power Resource [GFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 17
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 20
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 22 (level, low) -> IRQ 21
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 20
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 17 (level, low) -> IRQ 22
ACPI: PCI Interrupt 0000:04:01.1[B] -> GSI 18 (level, low) -> IRQ 20
ACPI: PCI Interrupt 0000:04:01.2[C] -> GSI 19 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:04:01.3[C] -> GSI 19 (level, low) -> IRQ 18
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f9f00000-fdffffff
PREFETCH window: bdf00000-ddefffff
PCI: Bridge: 0000:00:1c.0
IO window: c000-cfff
MEM window: fe000000-fe0fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
IO window: disabled.
MEM window: fe100000-fe1fffff
PREFETCH window: disabled.
PCI: Bus 5, cardbus bridge: 0000:04:01.0
IO window: 0000d000-0000d0ff
IO window: 0000d400-0000d4ff
PREFETCH window: 50000000-51ffffff
MEM window: 52000000-53ffffff
PCI: Bridge: 0000:00:1e.0
IO window: d000-dfff
MEM window: fe200000-feafffff
PREFETCH window: ddf00000-dfefffff
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 17 (level, low) -> IRQ 22
Simple Boot Flag at 0x52 set to 0x1
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.26 [Flags: R/O].
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Allocate Port Service[0000:00:1c.3:pcie03]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 20
ICH7: chipset revision 2
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: FUJITSU MHV2080AT PL, ATA DISK drive
hdb: TSSTcorpCD/DVDW TS-L532U, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 >
hdb: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbmon: debugfs is not available
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI Shortcut mode
EXT2-fs warning (device hda8): ext2_fill_super: mounting ext3 filesystem as ext2
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 220k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ieee1394: Initialized config rom entry `ip1394'
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000ec00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
i8xx TCO timer: heartbeat value must be 2<heartbeat<39, using 30
i8xx TCO timer: initialized (0x0860). heartbeat=30 sec (nowayout=0)
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000e880
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Linux agpgart interface v0.101 (c) Dave Jones
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 20, io base 0x0000e800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 21, io base 0x0000e480
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using uhci_hcd and address 2
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfebfbc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 17 (level, low) -> IRQ 22
Yenta: CardBus bridge found at 0000:04:01.0 [1043:1237]
Yenta: ISA IRQ mask 0x04b8, PCI irq 22
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xd000 - 0xdfff
cs: IO port probe 0xd000-0xdfff: clean.
pcmcia: parent PCI bridge Memory window: 0xfe200000 - 0xfeafffff
pcmcia: parent PCI bridge Memory window: 0xddf00000 - 0xdfefffff
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:04:01.1[B] -> GSI 18 (level, low) -> IRQ 20
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20] MMIO=[feaff800-feafffff] Max Packet=[2048] IR/IT contexts=[4/4]
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
agpgart: Detected an Intel 945GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
usb 1-2: device not accepting address 2, error -71
Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ALSA sound/pci/hda/hda_intel.c:634: codec_mask = 0x3
input: SynPS/2 Synaptics TouchPad as /class/input/input1
ALSA sound/pci/hda/hda_codec.c:1692: hda_codec: PCI 1043:1123, codec config 10 is selected
hw_random: RNG not detected
ts: Compaq touchscreen protocol output
usb 1-2: new low speed USB device using uhci_hcd and address 4
usb 1-2: configuration #1 chosen from 1 choice
input: HID 062a:0000 as /class/input/input2
input: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:1d.0-2
cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
cs: IO port probe 0x820-0x8ff: excluding 0x830-0x87f
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x400-0x41f 0x480-0x4bf 0x4d0-0x4d7
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0xa00-0xaff: clean.
nvidia: module license 'NVIDIA' taints kernel.
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8762 Mon May 15 13:06:38 PDT 2006
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800035597bf]
Adding 995988k swap on /dev/hda7. Priority:-1 extents:1 across:995988k
Capability LSM initialized
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS volume version 3.1.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: Identified chip type is 'RTL8168B/8111B'.
eth0: r10001.02, the Linux device driver for Realtek Ethernet Controllers at 0xc800, 00:17:31:34:03:63, IRQ 16
eth0: Auto-negotiation Enabled.
Realtek RTL8168/8111 Family PCI-E Gigabit Ethernet Network Adapter
Driver version:1.02
Released date:2006/02/23
Link Status:Not Linked
I/O Base:0xC800(I/O port)
IRQ:16
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, 1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.0.3d
ipw3945: Copyright(c) 2003-2006 Intel Corporation
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:03:00.0 to 64
ipw3945: Detected Intel PRO/Wireless 3945ABG Network Connection
Parsing all Control Methods:
Table [SSDT](id 0072) - 9 Objects with 0 Devices 4 Methods 0 Regions
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
Parsing all Control Methods:
Table [SSDT](id 0075) - 9 Objects with 0 Devices 4 Methods 0 Regions
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (68 C)
ACPI: AC Adapter [AC0] (on-line)
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Fan [FN00] (on)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ipw3945: Detected geography ABG (13 802.11bg channels, 23 802.11a channels)
