slacky.eu

Esiste un posto dove il sistema "registra" il boot nel senso dov'è, se c'è, che si possono leggere tutte quelle righe di informazioni che passano durante il boot? Perchè guardando lo schermo in fase di boot mi sono apparsi due error ma va talmente veloce che non riesco a capire di cosa si tratta. Grazie

premetto che sono ultra noob ma dovrebbe essere

dmesg

per comodita'

dmesg | less

??????????????
Mi sa proprio di no.

In un altro post è stato consigliato di lanciare pkgtool e poi scegliere setup...
Personalmente non ho mai provato (della serie non mi assumo responsabilità).
Ciao,
nino

Ho letto in un post qui su slacky di mettere in /etc/rc.d/rc.local

/etc/rc.d/rc.udev restart

l'ho fatto ed il risultato è un mezzo risultato nel senso che sono diminuite le righe
Intel ISA PCIC probe: not found.
c'è un po' di descrizione dell hardware. Cosa posso fare ancora?
Che devo fare con pkgtool?

Mi spiego meglio
dmesg
el ISA PCIC probe: not found.
Intel ISA PCIC probe: not found <-- 20 righe così
poi
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Intel ISA PCIC probe: not found <-- 80 righe così
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Intel ISA PCIC probe: not found <-- 180 righe così
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
eth0: no IPv6 routers present
NET: Registered protocol family 4
NET: Registered protocol family 3
NET: Registered protocol family 5
ReiserFS: hdd2: found reiserfs format "3.6" with standard journal
ReiserFS: hdd2: using ordered data mode
ReiserFS: hdd2: journal params: device hdd2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdd2: checking transaction log (hdd2)
ReiserFS: hdd2: Using r5 hash to sort names
usb 3-4: new high speed USB device using ehci_hcd and address 3
usb 3-4: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04B8 pid 0x081B
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new driver ub
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb 3-4: USB disconnect, address 3
drivers/usb/class/usblp.c: usblp0: removed
usb 3-4: new high speed USB device using ehci_hcd and address 4
usb 3-4: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x04B8 pid 0x081B
ISO 9660 Extensions: Microsoft Joliet Level 1
ISO 9660 Extensions: IEEE_P1282
drivers/usb/class/usblp.c: usblp0: on fire
drivers/usb/class/usblp.c: usblp0: nonzero read/write bulk status received: -71
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
usb 3-4: USB disconnect, address 4
drivers/usb/class/usblp.c: usblp0: removed
usb 3-4: new high speed USB device using ehci_hcd and address 5
usb 3-4: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x04B8 pid 0x081B
drivers/usb/class/usblp.c: usblp0: out of paper
drivers/usb/class/usblp.c: usblp0: nonzero read/write bulk status received: -71
printk: 7336 messages suppressed.
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
drivers/usb/class/usblp.c: usblp0: error -71 reading printer status
usb 3-4: USB disconnect, address 5
drivers/usb/class/usblp.c: usblp0: removed
usb 3-4: new high speed USB device using ehci_hcd and address 6
usb 3-4: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 6 if 0 alt 0 proto 2 vid 0x04B8 pid 0x081B
drivers/usb/class/usblp.c: usblp0: out of paper

Non mi sembra un output come quelli che leggo in giro di solito

Prova a dare ti dovrebbe azzerare il ring buffer del kernel, riportando l'ultimo boot!

6>Freeing unused kernel memory: 184k freed
Adding 1004020k swap on /dev/hdd1. Priority:-1 extents:1 across:1004020k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:10.1 -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 10, io base 0x0000e400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
input: PC Speaker as /class/input/input1
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[dfeff000-dfeff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:10.3: irq 10, io mem 0xdffffe00
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.101 (c) Dave Jones
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xec00, 00:4f:4e:61:1f:aa, IRQ 10
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
usb 3-4: new high speed USB device using ehci_hcd and address 3
usb 3-4: configuration #1 chosen from 1 choice
usb 1-2: new full speed USB device using uhci_hcd and address 2
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00308d0a0274f7a4]
nvidia: module license 'NVIDIA' taints kernel.
usb 1-2: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:11.5 to 64
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04B8 pid 0x081B
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new driver ub
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9746 Fri Dec 15 09:54:45 PST 2006
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
Intel ISA PCIC probe: not found.
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
20 RIGHE Intel ISA PCIC probe: not found.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
80 RIGHE Intel ISA PCIC probe: not found.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
180 RIGHE Intel ISA PCIC probe: not found.
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
eth0: no IPv6 routers present
NET: Registered protocol family 4
NET: Registered protocol family 3
NET: Registered protocol family 5

A parte il fatto che tutta sta pappina di roba non mi sembra quello che scorre al boot, ma mi devo preoccupare della frase
intel ISA PCIC probe: not found ????

Puoi anche scorrere /var/log/dmesg , per l'errore facendo una ricerca, sembra un bug del kernel, anche se non so se possa essere relazionato al tuo caso!

http://www.mail-archive.com/ubuntu-bugs ... 45790.html

Da quanto ho capito è un problema di rc.pcmcia... considerando che io ho slackware su un fisso, ho disabilitato lo script visto che nn uso schede pcmcia... ma dato che hai un portatile nn saprei come aiutarti ... spero ti aiuti il fatto che comunque il problema deriva da li...