slacky.eu

Codice: Seleziona tutto

-----
| pc01 | 192.168.1.100----------|
 -----                          |
192.168.0.100                   |
   |                            |
   |                            |  (wireless)    ----                 ------
   | (cavo cross)               |---------------| AP |---192.168.1.1 |router|-- INTERNET
   |                            |                ----                 ------
   |                            |
192.168.0.2                     |
 -----                          |
| pc01 | 192.168.1.2 -----------|
 -----

Codice: Seleziona tutto

root@slack12:/etc/rc.d# dmesg | grep zd121
usb 1-3.4: Could not load firmware file zd1211/zd1211_ub. Error number -2
zd1211rw 1-3.4:1.0: couldn't load firmware. Error number -2
zd1211rw: probe of 1-3.4:1.0 failed with error -2
usbcore: registered new interface driver zd1211rw

Codice: Seleziona tutto

root@slack12:/home/g4b0# lsusb
Bus 1 Device 4: ID 6891:a727
Bus 1 Device 3: ID 04a5:20de Acer Peripherals Inc. (now BenQ Corp.) S2W 4300U+
Bus 1 Device 2: ID 04cc:1521 Philips Semiconductors USB 2.0 Hub
Bus 1 Device 1: ID 0000:0000
Bus 5 Device 1: ID 0000:0000
Bus 4 Device 1: ID 0000:0000
Bus 3 Device 1: ID 0000:0000
Bus 2 Device 1: ID 0000:0000

Codice: Seleziona tutto

root@slack12:/home/g4b0# cat /usr/src/linux/drivers/net/wireless/zd1211rw/zd_usb.c |grep 0x6891
        { USB_DEVICE(0x6891, 0xa727), .driver_info = DEVICE_ZD1211 },

Codice: Seleziona tutto

# /etc/rc.d/rc.inet1.conf
#
# This file contains the configuration settings for network interfaces.
# If USE_DHCP[interface] is set to "yes", this overrides any other settings.
# If you don't have an interface, leave the settings null ("").

# You can configure network interfaces other than eth0,eth1... by setting
# IFNAME[interface] to the interface's name. If IFNAME[interface] is unset
# or empty, it is assumed you're configuring eth<interface>.

# Several other parameters are available, the end of this file contains a
# comprehensive set of examples.

# =============================================================================

# Config information for eth0:
IPADDR[0]="192.168.0.2"
NETMASK[0]="255.255.255.0"
USE_DHCP[0]=""
DHCP_HOSTNAME[0]=""

# Config information for eth1:
IPADDR[1]=""
NETMASK[1]=""
USE_DHCP[1]=""
DHCP_HOSTNAME[1]=""

# Config information for eth2:
IPADDR[2]=""
NETMASK[2]=""
USE_DHCP[2]=""
DHCP_HOSTNAME[2]=""

# Config information for eth3:
IPADDR[3]=""
NETMASK[3]=""
USE_DHCP[3]=""
DHCP_HOSTNAME[3]=""

# Default gateway IP address:
GATEWAY="192.168.0.1"

# Change this to "yes" for debugging output to stdout.  Unfortunately,
# /sbin/hotplug seems to disable stdout so you'll only see debugging output
# when rc.inet1 is called directly.
DEBUG_ETH_UP="no"

## Example config information for wlan0.  Uncomment the lines you need and fill
## in your info.  (You may not need all of these for your wireless network)
IFNAME[4]="wlan0"
IPADDR[4]="192.168.1.2"
NETMASK[4]="255.255.255.0"
USE_DHCP[4]="no"
#DHCP_HOSTNAME[4]="icculus-wireless"
#DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"
#DHCP_KEEPGW[4]="yes"
#DHCP_IPADDR[4]=""
WLAN_ESSID[4]=3com
WLAN_MODE[4]=Managed
WLAN_RATE[4]="54M auto"
WLAN_CHANNEL[4]="6"
#WLAN_KEY[4]="D5AD1F04ACF048EC2D0B1C80C7"
#WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP WPAPSK=7B1ABEEB5D197741923ED26727569C365E31212096A0EAFAD563B268BAD01CAF TxRate=0"
#WLAN_WPA[4]="wpa_supplicant"
#WLAN_WPADRIVER[4]="ndiswrapper"

## Some examples of additional network parameters that you can use.
## Config information for wlan0:
#IFNAME[4]="wlan0"              # Use a different interface name nstead of
                                # the default 'eth4'
#HWADDR[4]="00:01:23:45:67:89"  # Overrule the card's hardware MAC address
#MTU[4]=""                      # The default MTU is 1500, but you might need
                                # 1360 when you use NAT'ed IPSec traffic.
#DHCP_KEEPRESOLV[4]="yes"       # If you dont want /etc/resolv.conf overwritten
#DHCP_KEEPNTP[4]="yes"          # If you don't want ntp.conf overwritten
#DHCP_KEEPGW[4]="yes"           # If you don't want the DHCP server to change
                                # your default gateway
#DHCP_IPADDR[4]=""              # Request a specific IP address from the DHCP
                                # server
#WLAN_ESSID[4]=DARKSTAR         # Here, you can override _any_ parameter
                                # defined in rc.wireless.conf, by prepending
                                # 'WLAN_' to the parameter's name. Useful for
                                # those with multiple wireless interfaces.
#WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP WPAPSK=thekey TxRate=0"
                                # Some drivers require a private ioctl to be
                                # set through the iwpriv command. If more than
                                # one is required, you can place them in the
                                # IWPRIV parameter (space-separated, see the
                                # example).

Codice: Seleziona tutto

VERBOSE=0
WPA="n"

case "$HWADDR" in

00:0F:CB:*)
INFO="Configurazione wireless usb"
ESSID="3com"
MODE="Managed"
CHANNEL="11"
RATE="54M"

esac

#attiva il wpa se in rc.wireless.conf ne e' richiesta l'attivazione
if [ "$WPA" = "y" -a -x /usr/sbin/wpa_supplicant ]; then
 sleep 17 &&
 /usr/sbin/wpa_supplicant -B -c/etc/wpa_supplicant.conf -i${INTERFACE} -Dwext
fi

Codice: Seleziona tutto

/etc/rc.d/rc.inet1 stop
ifrename
/etc/rc.d/rc.inet1 start