slacky.eu

Codice: Seleziona tutto

bash-4.1# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11bg  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          
wlan1     IEEE 802.11bg  ESSID:"nome rete"  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=20 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:on

Codice: Seleziona tutto

bash-4.1# lspci
00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 10)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:05.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:12.0 IDE interface: ATI Technologies Inc IXP SB400 Serial ATA Controller (rev 80)
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (rev 80)
00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 83)
00:14.1 IDE interface: ATI Technologies Inc IXP SB400 IDE Controller (rev 80)
00:14.2 Audio device: ATI Technologies Inc IXP SB4x0 High Definition Audio Controller (rev 01)
00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc RS482 [Radeon Xpress 200M]
06:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
06:02.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
06:04.0 CardBus bridge: ENE Technology Inc CB-712/4 Cardbus Controller (rev 10)
06:04.1 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller (rev 01)
06:04.2 SD Host controller: ENE Technology Inc ENE PCI Secure Digital Card Reader Controller (rev 01)
06:04.3 FLASH memory: ENE Technology Inc FLASH memory: ENE Technology Inc: (rev 01)
06:04.4 FLASH memory: ENE Technology Inc SD/MMC Card Reader Controller (rev 01)
bash-4.1# 

Codice: Seleziona tutto

# /etc/rc.d/rc.inet1.conf
#
# This file contains the configuration settings for network interfaces.
# If USE_DHCP[interface] is set to "yes", this overrides any other settings.
# If you don't have an interface, leave the settings null ("").

# You can configure network interfaces other than eth0,eth1... by setting
# IFNAME[interface] to the interface's name. If IFNAME[interface] is unset
# or empty, it is assumed you're configuring eth<interface>.

# Several other parameters are available, the end of this file contains a
# comprehensive set of examples.

# =============================================================================

# Config information for eth0:
IPADDR[0]=""
NETMASK[0]=""
USE_DHCP[0]="yes"
DHCP_HOSTNAME[0]=""

# Config information for eth1:
IPADDR[1]=""
NETMASK[1]=""
USE_DHCP[1]=""
DHCP_HOSTNAME[1]=""

# Config information for eth2:
IPADDR[2]=""
NETMASK[2]=""
USE_DHCP[2]=""
DHCP_HOSTNAME[2]=""

# Config information for eth3:
IPADDR[3]=""
NETMASK[3]=""
USE_DHCP[3]=""
DHCP_HOSTNAME[3]=""

# Default gateway IP address:
GATEWAY=""

# Change this to "yes" for debugging output to stdout.  Unfortunately,
# /sbin/hotplug seems to disable stdout so you'll only see debugging output
# when rc.inet1 is called directly.
DEBUG_ETH_UP="no"

## Example config information for wlan0.  Uncomment the lines you need and fill
## in your info.  (You may not need all of these for your wireless network)
IFNAME[4]="wlan1"
#IPADDR[4]=""
#NETMASK[4]=""
USE_DHCP[4]="yes"
DHCP_HOSTNAME[4]="icculus-wireless"
DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"
#DHCP_KEEPGW[4]="yes"
#DHCP_IPADDR[4]=""
WLAN_ESSID[4]="nome rete"
WLAN_MODE[4]=Managed
##WLAN_RATE[4]="54M auto"
WLAN_CHANNEL[4]="auto"
WLAN_KEY[4]=passwordvf5rt63gf67753gft63uh6
##WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=96389dc66eaf7e6efd5b5523ae43c7925ff4df2f8b7099495192d44a774fda16"
WLAN_WPA[4]="wpa_supplicant"
WLAN_WPADRIVER[4]="wext"

## Some examples of additional network parameters that you can use.
## Config information for wlan0:
#IFNAME[4]="wlan0"              # Use a different interface name nstead of
                                # the default 'eth4'
#HWADDR[4]="00:01:23:45:67:89"  # Overrule the card's hardware MAC address
#MTU[4]=""                      # The default MTU is 1500, but you might need
                                # 1360 when you use NAT'ed IPSec traffic.
#DHCP_KEEPRESOLV[4]="yes"       # If you dont want /etc/resolv.conf overwritten
#DHCP_KEEPNTP[4]="yes"          # If you don't want ntp.conf overwritten
#DHCP_KEEPGW[4]="yes"           # If you don't want the DHCP server to change
                                # your default gateway
#DHCP_IPADDR[4]=""              # Request a specific IP address from the DHCP
                                # server
#WLAN_ESSID[4]=DARKSTAR         # Here, you can override _any_ parameter
                                # defined in rc.wireless.conf, by prepending
                                # 'WLAN_' to the parameter's name. Useful for
                                # those with multiple wireless interfaces.
#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=thekey"
                                # Some drivers require a private ioctl to be
                                # set through the iwpriv command. If more than
                                # one is required, you can place them in the
                                # IWPRIV parameter (separated with the pipe (|)
                                # character, see the example).

Codice: Seleziona tutto

# Wireless LAN adapter configuration
#
# Theory of operation : 
#
# The script attempts to match a block of settings to the specific wireless
# card inserted, the *first* block matching the card is used.
# The address format is "hwaddr", with * as a wildcard.
# 'hwaddr' is the unique MAC address identifier of the wireless card.
# The MAC address is usually printed on the card, or can be found via ifconfig.
# Some examples here use only half of the MAC address with a wildcard to
# match a whole family of cards...
#
# All the Wireless specific configuration is done through the Wireless
# Extensions, so we will just call 'iwconfig' with the right parameters
# defined below.
# Of course, you need to have iwconfig installled on your system.
# To download iwconfig, or for more info on Wireless Extensions :
#	http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html
#
# Note : you don't need to fill all parameters, leave them blank, in most
# cases the driver will initialise itself with sane defaults values or
# automatically figure out the value... And no drivers do support all
# possible settings...
#
# -- This is a modified '/etc/pcmcia/wireless.opts' script --
# -- I added sections for Prism/GT and Atheros based cards --
# --    (supported by the prism54 and madwifi drivers)     --
# --              16/sep/2004 * Eric Hameleers             --
#

VERBOSE=1

case "$HWADDR" in
00:1B:11:*)
[ -n ${WLAN_ESSID[$i]} ] && ${IWCOMMAND} essid ${WLAN_ESSID[$i]}
;;

## NOTE : Comment out the following five lines to activate the samples below ...
## --------- START SECTION TO REMOVE -----------
## Pick up any Access Point, should work on most 802.11 cards
#*)
 #   INFO="Any ESSID"
  #  ESSID="any"
   # ;;
## ---------- END SECTION TO REMOVE ------------


# Here are a few examples with a few Wireless LANs supported...
# The matching is done on the first 3 bytes of the MAC address

# SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter 
00:1b:11:*)
    INFO="SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter"
    # ESSID (extended network name) : My Network, any
    ESSID="rete asa d-link"
    # NWID/Domain (cell identifier) : 89AB, 100, off
    NWID=""
    # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
    MODE="Managed"
    # Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
    FREQ=""
    CHANNEL="6"
    # Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
    SENS=""
    # Bit rate : auto, 1M, 11M,54M
    RATE="auto"
    # Encryption key : 4567-89AB-CD, s:password
    # Example for 40-bit encryption:
    #KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
    # Example for 104-bit encryption (aka 128-bit WEP):
    #KEY="d5ad2f05abd048ecf10b1c80c7"
    KEY=sj48ddk98f7fg432as5bf8f9g765tgbvd56syd6s94j8fhst34bz7ddm573d
    # RTS threshold : off, 500
    RTS=""
    # Fragmentation threshold : off, 1000
    FRAG=""
    # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
    IWCONFIG=""
    # iwspy parameters : + 01:23:45:67:89:AB
    IWSPY=""
    # iwpriv parameters : set_port 2, set_histo 50 60
    IWPRIV=""
;;

# Multiband Atheros based 802.11a/b/g universal NIC cards
00:05:4E:*)
    INFO="Multiband Atheros based 802.11a/b/g universal NIC"
    # ESSID (extended network name) : My Network, any
    ESSID=""
    # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
    MODE="Managed"
    # Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
    FREQ=""
    CHANNEL="7"
    # Bit rate : auto, 1M, 11M,54M
    RATE="auto"
    # Encryption key : 4567-89AB-CD, s:password
    # Example for 40-bit encryption:
    #KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
    # Example for 104-bit encryption (aka 128-bit WEP):
    #KEY="d5ad2f05abd048ecf10b1c80c7"
    KEY=""
    # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
    IWCONFIG=""
    # iwspy parameters : + 01:23:45:67:89:AB
    IWSPY=""
    # iwpriv parameters : set_port 2, set_histo 50 60
    IWPRIV=""
    ;;

# Lucent Wavelan IEEE (+ Orinoco, RoamAbout and ELSA)
# Note : wvlan_cs driver only, and version 1.0.4+ for encryption support
00:60:1D:*|00:02:2D:*)
    INFO="Wavelan IEEE example (Lucent default settings)"
    ESSID="Wavelan Network"
    MODE="Managed"
    #RATE="auto"
    KEY="s:secu1"
    # To set all four keys, use :
    #KEY="s:secu1 [1] key s:secu2 [2] key s:secu3 [3] key s:secu4 [4] key [1]"
    # For the RG 1000 Residential Gateway: The ESSID is the identifier on
    # the unit, and the default key is the last 5 digits of the same.
    #ESSID="084d70"
    #KEY="s:84d70"
    ;;

# Cisco/Aironet 4800/3x0
# Note : MPL driver only (airo/airo_cs), version 1.3 or later
00:40:96:*|00:02:8A:*)
    INFO="Cisco/Aironet example (Cisco default settings)"
    ESSID="any"
    # To set all four ESSID, use iwconfig v21 and the same trick as above
    MODE="Managed"
    #RATE="11M auto"
    #KEY="d5ad2f05abd048ecf10b1c80c7"
    KEY="off"
    ;;

# Samsung MagicLan (+ some other PrismII cards)
# Note : Samsung binary library driver, version 1.20 or later
00:00:F0:*|00:02:78:*)
    INFO="Samsung MagicLan example (Samsung default settings)"
    ESSID="any"
    MODE="Managed"
    CHANNEL="4"
    RATE="auto"
    #KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
    #IWCONFIG="power on"
    ;;

# Raytheon Raylink/WebGear Aviator2.4
# Note : doesn't work yet, please use for debugging only :-(
00:00:8F:*|00:00:F1:*)
    INFO="Raylink/Aviator2.4 example (Aviator default ad-hoc setting)"
    ESSID="ADHOC_ESSID"
    MODE="Ad-Hoc"
    RATE="auto"
    IWPRIV="set_framing 1"
    ;;

# Old Lucent Wavelan
08:00:0E:*)
    INFO="Wavelan example (Lucent default settings)"
    NWID="0100"
    MODE="Ad-Hoc"
    FREQ="2.425G"
    KEY="off"
    ;;

# Netwave (Xircom Netwave/Netwave Airsurfer)
00:80:C7:*)
    INFO="Netwave example (Netwave default settings)"
    NWID="100"
    KEY="00"
    ;;

# Proxim RangeLan2/Symphony (what is the MAC address ???)
XX:XX:XX:*)
    INFO="Proxim RangeLan2/Symphony example"
    NWID="0"
    MODE="Master"
    CHANNEL="15"
    IWPRIV="setsubchan 1"
    ;;

# No Wires Needed Swallow 550 and 1100 setting (what is the MAC address ???)
XX:XX:XX:*)
    INFO="NWN Swallow example"
    ESSID="session"
    KEY="0000-0000-00 open"
    ;;

# Symbol Spectrum24 setting (what is the MAC address ???)
XX:XX:XX:*)
    INFO="Symbol Spectrum24 example"
    ESSID="Essid string"
    ;;

# Generic example (decribe all possible settings)
*)
    INFO="Fill with your own settings..."
    # ESSID (extended network name) : My Network, any
    ESSID=""
    # NWID/Domain (cell identifier) : 89AB, 100, off
    NWID=""
    # Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
    MODE=""
    # Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
    FREQ=""
    CHANNEL=""
    # Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
    SENS=""
    # Bit rate : auto, 1M, 11M
    RATE=""
    # Encryption key : 4567-89AB-CD, s:password
    KEY=""
    # RTS threshold : off, 500
    RTS=""
    # Fragmentation threshold : off, 1000
    FRAG=""
    # Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
    IWCONFIG=""
    # iwspy parameters : + 01:23:45:67:89:AB
    IWSPY=""
    # iwpriv parameters : set_port 2, set_histo 50 60
    IWPRIV=""
    ;;
esac

Codice: Seleziona tutto

# See /usr/doc/wpa_supplicant-0.7.3/wpa_supplicant.conf.sample
# for many more options that you can use in this file.

# This line enables the use of wpa_cli which is used by rc.wireless
# if possible (to check for successful association)
ctrl_interface=/var/run/wpa_supplicant
# By default, only root (group 0) may use wpa_cli
ctrl_interface_group=wheel
eapol_version=1
ap_scan=1
fast_reauth=1
#country=US

# WPA protected network, supply your own ESSID and WPAPSK here:
network={
  scan_ssid=0
  ssid="rete casa d-link"
  proto=WPA
  key_mgmt=WPA-PSK
  pairwise=CCMP TKIP
  group=CCMP TKIP WEP104 WEP40
  psk=passwordby6e78y6yhdff45gshbsfs54vbsbs
  priority=10
}

# Plaintext connection (no WPA, no IEEE 802.1X),
# nice for hotel/airport types of WiFi network.
network={
  key_mgmt=NONE
  priority=0
}

Codice: Seleziona tutto

modprobe -r b43
dmesg -c
modprobe b43

Codice: Seleziona tutto

dmesg

Codice: Seleziona tutto

root@sato:/etc# dmesg
[ 6274.490654] b43-pci-bridge 0000:06:02.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 6274.498240] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
[ 6274.498266] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
[ 6274.498287] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
[ 6274.498306] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
[ 6274.520177] ssb: Sonics Silicon Backplane found on PCI device 0000:06:02.0
[ 6274.554396] b43-phy3: Broadcom 4318 WLAN found (core revision 9)
[ 6274.576265] ieee80211 phy3: Selected rate control algorithm 'minstrel_ht'
[ 6274.576502] Registered led device: b43-phy3::tx
[ 6274.576531] Registered led device: b43-phy3::rx
[ 6274.576558] Registered led device: b43-phy3::radio
[ 6274.576579] Broadcom 43xx driver loaded [ Features: PMLS, Firmware-ID: FW13 ]
[ 6274.824097] b43-phy3 ERROR: Firmware file "b43/ucode5.fw" not found
[ 6274.824102] b43-phy3 ERROR: Firmware file "b43-open/ucode5.fw" not found
[ 6274.824105] b43-phy3 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.

Codice: Seleziona tutto

root@sato:/lib/firmware/brcm# dmesg
[ 8832.092992] brcm80211: module is from the staging directory, the quality is unknown, you have been warned.

Codice: Seleziona tutto

lspci -vv -s 06:02.0 

Codice: Seleziona tutto

.

Emanuele

Codice: Seleziona tutto

root@sato:/lib/firmware/brcm# lspci -vv -s 06:02.0
06:02.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
        Subsystem: AMBIT Microsystem Corp. TravelMate 2410
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 64
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at b0200000 (32-bit, non-prefetchable) [size=8K]
        Kernel driver in use: b43-pci-bridge
        Kernel modules: ssb

Codice: Seleziona tutto

lspci -nn -s 06:02.0

Codice: Seleziona tutto

root@sato:/lib/firmware/brcm# lspci -nn -s 06:02.0
06:02.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)

Codice: Seleziona tutto

wget http://bu3sch.de/b43/fwcutter/b43-fwcutter-015.tar.bz2
tar -xf b43-fwcutter-015.tar.bz2
cd b43-fwcutter-015
make
cd ..
wget http://www.lwfinger.com/b43-firmware/broadcom-wl-5.100.138.tar.bz2
tar -xf broadcom-wl-5.100.138.tar.bz2

Codice: Seleziona tutto

b43-fwcutter-015/b43-fwcutter -w /lib/firmware broadcom-wl-5.100.138/linux/wl_apsta.o

Codice: Seleziona tutto

/lib/firmware/b43/

Codice: Seleziona tutto

modprobe -r ssb
modprobe -r b43
dmesg -c
modprobe b43

Codice: Seleziona tutto

dmesg

Codice: Seleziona tutto

b43-fwcutter-015/b43-fwcutter