Non cè nessuno che sa come fare? Non so se può essere utile comunque questo è il mio dmesg
Codice: Seleziona tutto
ame buffer device
ACPI: CPU0 (power states: C1[C1])
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
smapi::smapi_init, ERROR invalid usSmapiID
mwave: tp3780i::tp3780I_InitializeBoardData: Error: SMAPI is not available on th
is machine
mwave: mwavedd::mwave_init: Error: Failed to initialize board data
mwave: mwavedd::mwave_init: Error: Failed to initialize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 7777K size 1024 blocksize
loop: loaded (max 8 devices)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ
10
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ
10
sk98lin: Asus mainboard with buggy VPD? Correcting data.
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: PIONEER DVD-RW DVR-107D, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
hdc: Maxtor 6Y120L0, ATA DISK drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 128KiB
hdc: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=65535/16/63
hdc: cache flushes supported
hdc: hdc1 hdc2
hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 7157.000 MB/sec
raid5: using function: pIII_sse (7157.000 MB/sec)
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
Advanced Linux Sound Architecture Driver Version 1.0.9b (Thu Jul 28 12:20:13 200
5 UTC).
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.3)
powernow-k8: BIOS error - no PSB or ACPI _PSS objects
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 PS2K PS2M UAR2 UAR1 AC97 USB1 USB2 USB3 USB4 EHCI PWRB SLPB
ACPI: (supports S0 S1 S3 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
ReiserFS: hdc2: found reiserfs format "3.6" with standard journal
logips2pp: Detected unknown logitech mouse model 86
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
ReiserFS: hdc2: using ordered data mode
ReiserFS: hdc2: journal params: device hdc2, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdc2: checking transaction log (hdc2)
ReiserFS: hdc2: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 196k freed
Adding 2000052k swap on /dev/hdc1. Priority:-1 extents:1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
Linux agpgart interface v0.101 (c) Dave Jones
Linux video capture interface: v1.00
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver ov511
drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver
ndiswrapper version 1.3rc1 loaded (preempt=no,smp=no)
ndiswrapper: driver tnet1130 (Texas Instruments,03/10/2004,6.0.0.18) loaded
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ
10
ndiswrapper: using irq 10
wlan0: ndiswrapper ethernet device 00:e0:98:d8:88:11 using driver tnet1130, conf
iguration file 104C:9066:13D1:AB90.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggeredACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ
11
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7174 Tue Mar 22 06:44:
39 PST 2005
Creative EMU10K1 PCI Audio Driver, version 0.20a, 21:58:54 Jan 2 2006
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ
5
emu10k1: EMU10K1 rev 7 model 0x8026 found, IO at 0xa800-0xa81f, IRQ 5
ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
vt596_smbus 0000:00:11.0: using Interrupt SMI# for SMBus.
vt596_smbus 0000:00:11.0: SMBREV = 0x0
vt596_smbus 0000:00:11.0: VT596_smba = 0x400
i2c_adapter i2c-0: registered as adapter #0
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ
5
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: reset hcs_params 0x4208 dbg=0 cc=4 pcc=2 ordered !ppc por
ts=8
ehci_hcd 0000:00:10.4: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:00:10.4: capability 0001 at 68
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 5, io mem 0xf7f00000
ehci_hcd 0000:00:10.4: reset command 080002 (park)=0 ithresh=8 period=1024 Reset
HALT
ehci_hcd 0000:00:10.4: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ehci_hcd 0000:00:10.4: supports USB remote wakeup
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: VIA Technologies, Inc. USB 2.0
usb usb1: Manufacturer: Linux 2.6.13.2 ehci_hcd
usb usb1: SerialNumber: 0000:00:10.4
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: state 5 ports 8 chg 0000 evt 0000
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ
11
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: detected 2 ports
uhci_hcd 0000:00:10.0: check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.0: Performing full reset
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000b400
uhci_hcd 0000:00:10.0: supports USB remote wakeup
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
usb usb2: Manufacturer: Linux 2.6.13.2 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ
11
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#2)
uhci_hcd 0000:00:10.1: detected 2 ports
uhci_hcd 0000:00:10.1: check_and_reset_hc: legsup = 0x8030
uhci_hcd 0000:00:10.1: Performing full reset
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.0: port 1 portsc 008a,00
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 11, io base 0x0000b800
uhci_hcd 0000:00:10.1: supports USB remote wakeup
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
usb usb3: Manufacturer: Linux 2.6.13.2 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.0: port 2 portsc 018a,00
hub 2-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0000
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
eth0: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: none
irq moderation: disabled
scatter-gather: enabled
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ
10
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#3)
uhci_hcd 0000:00:10.2: detected 2 ports
uhci_hcd 0000:00:10.2: check_and_reset_hc: legsup = 0x8030
uhci_hcd 0000:00:10.2: Performing full reset
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.1: port 1 portsc 018a,00
hub 3-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 10, io base 0x0000c000
uhci_hcd 0000:00:10.2: supports USB remote wakeup
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
usb usb4: Manufacturer: Linux 2.6.13.2 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
uhci_hcd 0000:00:10.1: port 2 portsc 008a,00
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0000
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
uhci_hcd 0000:00:10.0: suspend_rh (auto-stop)
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ
10
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#4)
uhci_hcd 0000:00:10.3: detected 2 ports
uhci_hcd 0000:00:10.3: check_and_reset_hc: legsup = 0x8030
uhci_hcd 0000:00:10.3: Performing full reset
hub 4-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.2: port 1 portsc 018a,00
hub 4-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 10, io base 0x0000c400
uhci_hcd 0000:00:10.3: supports USB remote wakeup
usb usb5: default language 0x0409
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
usb usb5: Manufacturer: Linux 2.6.13.2 uhci_hcd
usb usb5: SerialNumber: 0000:00:10.3
usb usb5: hotplug
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: hotplug
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: power on to power good time: 2ms
hub 5-0:1.0: local power source is good
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
uhci_hcd 0000:00:10.2: port 2 portsc 018a,00
hub 4-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 4-0:1.0: state 5 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.3: port 1 portsc 018a,00
hub 5-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:10.1: suspend_rh (auto-stop)
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1299 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ
11
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[f7800000-f78007ff] Max
Packet=[2048]
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
uhci_hcd 0000:00:10.3: port 2 portsc 018a,00
hub 5-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
hub 5-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 5-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
hub 5-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf8000000
uhci_hcd 0000:00:10.2: suspend_rh (auto-stop)
uhci_hcd 0000:00:10.3: suspend_rh (auto-stop)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0180000b1c629]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP]
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
lp0: using parport0 (interrupt-driven).
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled on user request.
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
scusate per la lunghezza, comunque mentre lo copiavo mi sono accorto degli innumerevoli errori di cui non sapevo l'esistenza.
