ecco il dmesg di arch:
Codice: Seleziona tutto
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.0.5-1-ARCH (builduser@tobias) (gcc version 5.1.0 (GCC) ) #1 SMP PREEMPT Sat Jun 6 18:52:28 CEST 2015
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000004fffbfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000004fffc000-0x000000004fffefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000004ffff000-0x000000004fffffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffff0000-0x00000000ffffffff] reserved
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] SMBIOS 2.3 present.
[ 0.000000] DMI: System Manufacturer System Name/A7V8X-X, BIOS ASUS A7V8X-X ACPI BIOS Revision 1013 09/02/2004
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x4fffc max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FC0000000 write-back
[ 0.000000] 1 base 040000000 mask FF0000000 write-back
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 base 0F8000000 mask FFC000000 write-combining
[ 0.000000] PAT configuration [0-7]: WB WC UC- UC WB WC UC- UC
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] initial memory mapped: [mem 0x00000000-0x01bfffff]
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x37000000-0x373fffff]
[ 0.000000] [mem 0x37000000-0x373fffff] page 4M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x36ffffff]
[ 0.000000] [mem 0x00100000-0x003fffff] page 4k
[ 0.000000] [mem 0x00400000-0x36ffffff] page 4M
[ 0.000000] init_memory_mapping: [mem 0x37400000-0x377fdfff]
[ 0.000000] [mem 0x37400000-0x377fdfff] page 4k
[ 0.000000] BRK [0x017e3000, 0x017e3fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x378d8000-0x37c63fff]
[ 0.000000] Allocated new RAMDISK: [mem 0x37472000-0x377fd247]
[ 0.000000] Move RAMDISK from [mem 0x378d8000-0x37c63247] to [mem 0x37472000-0x377fd247]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F5E20 000014 (v00 ASUS )
[ 0.000000] ACPI: RSDT 0x000000004FFFC000 000030 (v01 ASUS A7V8X-X 42302E31 MSFT 31313031)
[ 0.000000] ACPI: FACP 0x000000004FFFC0B2 000074 (v01 ASUS A7V8X-X 42302E31 MSFT 31313031)
[ 0.000000] ACPI: DSDT 0x000000004FFFC126 002A13 (v01 ASUS A7V8X-X 00001000 MSFT 0100000B)
[ 0.000000] ACPI: FACS 0x000000004FFFF000 000040
[ 0.000000] ACPI: BOOT 0x000000004FFFC030 000028 (v01 ASUS A7V8X-X 42302E31 MSFT 31313031)
[ 0.000000] ACPI: APIC 0x000000004FFFC058 00005A (v01 ASUS A7V8X-X 42302E31 MSFT 31313031)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 391MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] BRK [0x017e4000, 0x017e4fff] PGTABLE
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] Normal [mem 0x0000000001000000-0x00000000377fdfff]
[ 0.000000] HighMem [mem 0x00000000377fe000-0x000000004fffbfff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009efff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000004fffbfff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000004fffbfff]
[ 0.000000] On node 0 totalpages: 327578
[ 0.000000] free_area_init_node: node 0, pgdat c165e640, node_mem_map f67f2028
[ 0.000000] DMA zone: 40 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] Normal zone: 2180 pages used for memmap
[ 0.000000] Normal zone: 223230 pages, LIFO batch:31
[ 0.000000] HighMem zone: 100350 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0xe408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] smpboot: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] e820: [mem 0x50000000-0xfebfffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 16 pages/cpu @f67db000 s36812 r0 d28724 u65536
[ 0.000000] pcpu-alloc: s36812 r0 d28724 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 325358
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=0f5b3322-df7e-4fcc-9cad-9adca983c044 rw quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000377fe:0004fffc)
[ 0.000000] Initializing Movable for node 0 (00000000:00000000)
[ 0.000000] Memory: 1284828K/1310312K available (4747K kernel code, 440K rwdata, 1404K rodata, 588K init, 828K bss, 25484K reserved, 0K cma-reserved, 401400K highmem)
[ 0.000000] virtual kernel memory layout:
fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1674000 - 0xc1707000 ( 588 kB)
.data : 0xc14a325b - 0xc16722c0 (1852 kB)
.text : 0xc1000000 - 0xc14a325b (4748 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS:2304 nr_irqs:256 16
[ 0.000000] CPU 0 irqstacks, hard=f6030000 soft=f6032000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 1099.983 MHz processor
[ 0.003361] Calibrating delay loop (skipped), value calculated using timer frequency.. 2200.63 BogoMIPS (lpj=3666610)
[ 0.003373] pid_max: default: 32768 minimum: 301
[ 0.003403] ACPI: Core revision 20150204
[ 0.010267] ACPI: All ACPI Tables successfully acquired
[ 0.013427] Security Framework initialized
[ 0.013461] Yama: becoming mindful.
[ 0.013505] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.013513] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.014256] Initializing cgroup subsys blkio
[ 0.014271] Initializing cgroup subsys memory
[ 0.014305] Initializing cgroup subsys devices
[ 0.014317] Initializing cgroup subsys freezer
[ 0.014328] Initializing cgroup subsys net_cls
[ 0.014389] mce: CPU supports 4 MCE banks
[ 0.014418] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.014423] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[ 0.023906] Freeing SMP alternatives memory: 20K (c1707000 - c170c000)
[ 0.025446] ftrace: allocating 20198 entries in 40 pages
[ 0.037000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.040628] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.076666] smpboot: CPU0: AMD Athlon(TM) XP 1700+ (fam: 06, model: 08, stepping: 01)
[ 0.076666] Performance Events: AMD PMU driver.
[ 0.076666] ... version: 0
[ 0.076666] ... bit width: 48
[ 0.076666] ... generic registers: 4
[ 0.076666] ... value mask: 0000ffffffffffff
[ 0.076666] ... max period: 00007fffffffffff
[ 0.076666] ... fixed-purpose events: 0
[ 0.076666] ... event mask: 000000000000000f
[ 0.086686] x86: Booted up 1 node, 1 CPUs
[ 0.086701] smpboot: Total of 1 processors activated (2200.63 BogoMIPS)
[ 0.087573] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.087911] devtmpfs: initialized
[ 0.088630] PM: Registering ACPI NVS region [mem 0x4ffff000-0x4fffffff] (4096 bytes)
[ 0.089090] pinctrl core: initialized pinctrl subsystem
[ 0.089181] RTC time: 20:02:50, date: 07/03/15
[ 0.089618] NET: Registered protocol family 16
[ 0.106679] cpuidle: using governor ladder
[ 0.120009] cpuidle: using governor menu
[ 0.120192] ACPI: bus type PCI registered
[ 0.120201] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.122111] PCI: PCI BIOS revision 2.10 entry at 0xf1960, last bus=1
[ 0.122116] PCI: Using configuration type 1 for base access
[ 0.138264] ACPI: Added _OSI(Module Device)
[ 0.138277] ACPI: Added _OSI(Processor Device)
[ 0.138282] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.138286] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.146684] ACPI: Interpreter enabled
[ 0.146728] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150204/hwxface-580)
[ 0.146742] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20150204/hwxface-580)
[ 0.146769] ACPI: (supports S0 S1 S4 S5)
[ 0.146775] ACPI: Using IOAPIC for interrupt routing
[ 0.146871] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.160234] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12)
[ 0.160404] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
[ 0.160565] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
[ 0.160725] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12) *0, disabled.
[ 0.160953] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12)
[ 0.161204] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 9 10 11 12)
[ 0.161358] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.161525] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.161546] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI]
[ 0.161561] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.161710] acpi PNP0A03:00: host bridge window [io 0x0000-0x0cf7 window] (ignored)
[ 0.161718] acpi PNP0A03:00: host bridge window [io 0x0d00-0xffff window] (ignored)
[ 0.161725] acpi PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff window] (ignored)
[ 0.161732] acpi PNP0A03:00: host bridge window [mem 0x000c8000-0x000dffff window] (ignored)
[ 0.161738] acpi PNP0A03:00: host bridge window [mem 0x50000000-0xfebfffff window] (ignored)
[ 0.161743] PCI: root bus 00: using default resources
[ 0.161752] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[ 0.162068] PCI host bridge to bus 0000:00
[ 0.162080] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.162087] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.162094] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
[ 0.162129] pci 0000:00:00.0: [1106:3189] type 00 class 0x060000
[ 0.162153] pci 0000:00:00.0: reg 0x10: [mem 0xf8000000-0xfbffffff pref]
[ 0.162420] pci 0000:00:01.0: [1106:b198] type 01 class 0x060400
[ 0.162488] pci 0000:00:01.0: supports D1
[ 0.162571] pci 0000:00:01.0: System wakeup disabled by ACPI
[ 0.162743] pci 0000:00:0d.0: [1106:3044] type 00 class 0x0c0010
[ 0.162768] pci 0000:00:0d.0: reg 0x10: [mem 0xed800000-0xed8007ff]
[ 0.162783] pci 0000:00:0d.0: reg 0x14: [io 0xd800-0xd87f]
[ 0.162865] pci 0000:00:0d.0: supports D2
[ 0.162872] pci 0000:00:0d.0: PME# supported from D2 D3hot D3cold
[ 0.163081] pci 0000:00:10.0: [1106:3038] type 00 class 0x0c0300
[ 0.163136] pci 0000:00:10.0: reg 0x20: [io 0xd400-0xd41f]
[ 0.163191] pci 0000:00:10.0: supports D1 D2
[ 0.163197] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.163261] pci 0000:00:10.0: System wakeup disabled by ACPI
[ 0.163446] pci 0000:00:10.1: [1106:3038] type 00 class 0x0c0300
[ 0.163501] pci 0000:00:10.1: reg 0x20: [io 0xd000-0xd01f]
[ 0.163557] pci 0000:00:10.1: supports D1 D2
[ 0.163563] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.163628] pci 0000:00:10.1: System wakeup disabled by ACPI
[ 0.163798] pci 0000:00:10.2: [1106:3038] type 00 class 0x0c0300
[ 0.163853] pci 0000:00:10.2: reg 0x20: [io 0xb800-0xb81f]
[ 0.163907] pci 0000:00:10.2: supports D1 D2
[ 0.163913] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.163977] pci 0000:00:10.2: System wakeup disabled by ACPI
[ 0.164141] pci 0000:00:10.3: [1106:3104] type 00 class 0x0c0320
[ 0.164164] pci 0000:00:10.3: reg 0x10: [mem 0xed000000-0xed0000ff]
[ 0.164250] pci 0000:00:10.3: supports D1 D2
[ 0.164256] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.164320] pci 0000:00:10.3: System wakeup disabled by ACPI
[ 0.164491] pci 0000:00:11.0: [1106:3177] type 00 class 0x060100
[ 0.164568] HPET not enabled in BIOS. You might try hpet=force boot option
[ 0.164586] pci 0000:00:11.0: can't claim BAR 13 [io 0xe400-0xe47f]: address conflict with ACPI PM1a_EVT_BLK [io 0xe400-0xe403]
[ 0.164595] pci 0000:00:11.0: quirk: [io 0xe800-0xe80f] claimed by vt8235 SMB
[ 0.164798] pci 0000:00:11.1: [1106:0571] type 00 class 0x01018a
[ 0.164856] pci 0000:00:11.1: reg 0x20: [io 0xb400-0xb40f]
[ 0.164883] pci 0000:00:11.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.164889] pci 0000:00:11.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.164894] pci 0000:00:11.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.164900] pci 0000:00:11.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.165124] pci 0000:00:11.5: [1106:3059] type 00 class 0x040100
[ 0.165148] pci 0000:00:11.5: reg 0x10: [io 0xe000-0xe0ff]
[ 0.165238] pci 0000:00:11.5: supports D1 D2
[ 0.165420] pci 0000:00:12.0: [1106:3065] type 00 class 0x020000
[ 0.165444] pci 0000:00:12.0: reg 0x10: [io 0xb000-0xb0ff]
[ 0.165458] pci 0000:00:12.0: reg 0x14: [mem 0xec800000-0xec8000ff]
[ 0.165538] pci 0000:00:12.0: supports D1 D2
[ 0.165544] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.165619] pci 0000:00:12.0: System wakeup disabled by ACPI
[ 0.165897] pci 0000:01:00.0: [10de:0322] type 00 class 0x030000
[ 0.165920] pci 0000:01:00.0: reg 0x10: [mem 0xee000000-0xeeffffff]
[ 0.165933] pci 0000:01:00.0: reg 0x14: [mem 0xf0000000-0xf7ffffff pref]
[ 0.165972] pci 0000:01:00.0: reg 0x30: [mem 0xeffe0000-0xefffffff pref]
[ 0.166168] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.166181] pci 0000:00:01.0: bridge window [mem 0xee000000-0xefefffff]
[ 0.166189] pci 0000:00:01.0: bridge window [mem 0xeff00000-0xf7ffffff pref]
[ 0.166203] pci_bus 0000:00: on NUMA node 0
[ 0.169472] ACPI: Enabled 1 GPEs in block 00 to 0F
[ 0.169855] vgaarb: setting as boot device: PCI:0000:01:00.0
[ 0.169863] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.169867] vgaarb: loaded
[ 0.169871] vgaarb: bridge control possible 0000:01:00.0
[ 0.170228] PCI: Using ACPI for IRQ routing
[ 0.170240] PCI: pci_cache_line_size set to 32 bytes
[ 0.170299] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 0.170306] e820: reserve RAM buffer [mem 0x4fffc000-0x4fffffff]
[ 0.170766] NetLabel: Initializing
[ 0.170772] NetLabel: domain hash size = 128
[ 0.170775] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.170814] NetLabel: unlabeled traffic allowed by default
[ 0.170943] Switched to clocksource refined-jiffies
[ 0.191068] pnp: PnP ACPI init
[ 0.191551] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.191561] system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
[ 0.191568] system 00:00: [mem 0x00100000-0x4fffffff] could not be reserved
[ 0.191576] system 00:00: [mem 0xfec00000-0xfec000ff] could not be reserved
[ 0.191583] system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.191595] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.192185] system 00:01: [io 0xe400-0xe47f] could not be reserved
[ 0.192195] system 00:01: [io 0xe800-0xe81f] could not be reserved
[ 0.192203] system 00:01: [mem 0xfff80000-0xffffffff] could not be reserved
[ 0.192210] system 00:01: [mem 0xffb80000-0xffbfffff] has been reserved
[ 0.192218] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.192418] system 00:02: [io 0x04d0-0x04d1] has been reserved
[ 0.192429] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.192704] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.193101] pnp 00:04: [dma 2]
[ 0.193214] pnp 00:04: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.194155] pnp 00:05: [dma 3]
[ 0.194291] pnp 00:05: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.195100] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.195866] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.196096] pnp 00:08: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
[ 0.197230] pnp 00:09: Plug and Play ACPI device, IDs PNPb02f (active)
[ 0.197396] system 00:0a: [io 0x0290-0x0297] has been reserved
[ 0.197405] system 00:0a: [io 0x0370-0x0375] has been reserved
[ 0.197414] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.197458] pnp: PnP ACPI: found 11 devices
[ 0.238855] Switched to clocksource acpi_pm
[ 0.238926] pci 0000:00:11.0: BAR 13: [io 0xe400-0xe47f] has bogus alignment
[ 0.238940] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.238956] pci 0000:00:01.0: bridge window [mem 0xee000000-0xefefffff]
[ 0.238966] pci 0000:00:01.0: bridge window [mem 0xeff00000-0xf7ffffff pref]
[ 0.238980] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.238987] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
[ 0.238994] pci_bus 0000:01: resource 1 [mem 0xee000000-0xefefffff]
[ 0.239000] pci_bus 0000:01: resource 2 [mem 0xeff00000-0xf7ffffff pref]
[ 0.239126] NET: Registered protocol family 2
[ 0.239792] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.239894] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.239894] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.239894] TCP: reno registered
[ 0.239894] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.239894] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.239894] NET: Registered protocol family 1
[ 0.239894] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[ 0.240392] pci 0000:01:00.0: Video device with shadowed ROM
[ 0.240401] PCI: CLS 32 bytes, default 32
[ 0.240596] Unpacking initramfs...
[ 0.449613] Freeing initrd memory: 3632K (f7472000 - f77fe000)
[ 0.449729] Simple Boot Flag at 0x3a set to 0x1
[ 0.450088] microcode: AMD CPU family 0x6 not supported
[ 0.450138] apm: BIOS not found.
[ 0.450304] Scanning for low memory corruption every 60 seconds
[ 0.451489] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.451539] Initialise system trusted keyring
[ 0.452466] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.459426] zpool: loaded
[ 0.459436] zbud: loaded
[ 0.459960] VFS: Disk quotas dquot_6.5.2
[ 0.460143] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.460869] Key type big_key registered
[ 0.461365] bounce: pool size: 64 pages
[ 0.461510] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.461612] io scheduler noop registered
[ 0.461621] io scheduler deadline registered
[ 0.461761] io scheduler cfq registered (default)
[ 0.462119] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.462187] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.462340] GHES: HEST is not enabled!
[ 0.462405] isapnp: Scanning for PnP cards...
[ 0.818724] isapnp: No Plug & Play device found
[ 0.818914] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.839518] 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 0.840916] rtc_cmos 00:03: RTC can wake from S4
[ 0.841207] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.841280] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram
[ 0.841405] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.841777] TCP: cubic registered
[ 0.842383] NET: Registered protocol family 10
[ 0.843054] NET: Registered protocol family 17
[ 0.843587] Using IPI No-Shortcut mode
[ 0.844041] Loading compiled-in X.509 certificates
[ 0.844095] registered taskstats version 1
[ 0.845039] Magic number: 7:314:42
[ 0.845248] rtc_cmos 00:03: setting system clock to 2015-07-03 20:02:51 UTC (1435953771)
[ 0.845462] PM: Hibernation image not present or could not be loaded.
[ 0.847173] Freeing unused kernel memory: 588K (c1674000 - c1707000)
[ 0.847251] Write protecting the kernel text: 4752k
[ 0.847329] Write protecting the kernel read-only data: 1408k
[ 0.874060] random: systemd-tmpfile urandom read with 0 bits of entropy available
[ 0.969425] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.981737] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.986240] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.993577] Floppy drive(s): fd0 is 1.44M
[ 1.010792] FDC 0 is a post-1991 82077
[ 1.042994] SCSI subsystem initialized
[ 1.047184] ACPI: bus type USB registered
[ 1.047296] usbcore: registered new interface driver usbfs
[ 1.047347] usbcore: registered new interface driver hub
[ 1.049761] usbcore: registered new device driver usb
[ 1.051840] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.052501] ehci-pci: EHCI PCI platform driver
[ 1.053004] ehci-pci 0000:00:10.3: EHCI Host Controller
[ 1.053030] ehci-pci 0000:00:10.3: new USB bus registered, assigned bus number 1
[ 1.053185] ehci-pci 0000:00:10.3: irq 21, io mem 0xed000000
[ 1.055036] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.060333] ehci-pci 0000:00:10.3: USB 2.0 started, EHCI 1.00
[ 1.061035] hub 1-0:1.0: USB hub found
[ 1.061065] hub 1-0:1.0: 6 ports detected
[ 1.065109] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 1.065140] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 1.065158] uhci_hcd 0000:00:10.0: detected 2 ports
[ 1.065199] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000d400
[ 1.065897] hub 2-0:1.0: USB hub found
[ 1.065926] hub 2-0:1.0: 2 ports detected
[ 1.092283] libata version 3.00 loaded.
[ 1.126822] firewire_ohci 0000:00:0d.0: added OHCI v1.0 device as card 0, 4 IR + 8 IT contexts, quirks 0x41
[ 1.127840] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 1.127871] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 1.127893] uhci_hcd 0000:00:10.1: detected 2 ports
[ 1.127934] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000d000
[ 1.128689] hub 3-0:1.0: USB hub found
[ 1.128719] hub 3-0:1.0: 2 ports detected
[ 1.129145] pata_via 0000:00:11.1: version 0.3.4
[ 1.129410] pata_via 0000:00:11.1: can't derive routing for PCI INT A
[ 1.138282] scsi host0: pata_via
[ 1.145379] scsi host1: pata_via
[ 1.145640] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xb400 irq 14
[ 1.145648] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xb408 irq 15
[ 1.146429] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 1.146462] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 1.146483] uhci_hcd 0000:00:10.2: detected 2 ports
[ 1.146524] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000b800
[ 1.147320] hub 4-0:1.0: USB hub found
[ 1.147351] hub 4-0:1.0: 2 ports detected
[ 1.172330] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.310511] ata1.00: ATA-7: SAMSUNG SP0802N, TK100-30, max UDMA/100
[ 1.310527] ata1.00: 156368016 sectors, multi 16: LBA48
[ 1.310676] ata1.01: ATA-7: SAMSUNG SP1604N, TM100-30, max UDMA/133
[ 1.310683] ata1.01: 312581808 sectors, multi 16: LBA48
[ 1.317336] ata1.00: configured for UDMA/100
[ 1.323671] ata1.01: configured for UDMA/133
[ 1.324024] scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP0802N 0-30 PQ: 0 ANSI: 5
[ 1.324837] scsi 0:0:1:0: Direct-Access ATA SAMSUNG SP1604N 0-30 PQ: 0 ANSI: 5
[ 1.450031] tsc: Refined TSC clocksource calibration: 1100.038 MHz
[ 1.490383] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-4163B, A102, max UDMA/33
[ 1.490400] ata2.01: ATAPI: HL-DT-STDVD-ROM GDR8164B, 0L06, max UDMA/33
[ 1.503575] ata2.00: configured for UDMA/33
[ 1.516910] ata2.01: configured for UDMA/33
[ 1.529084] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-4163B A102 PQ: 0 ANSI: 5
[ 1.542634] scsi 1:0:1:0: CD-ROM HL-DT-ST DVD-ROM GDR8164B 0L06 PQ: 0 ANSI: 5
[ 1.550141] usb 2-1: new full-speed USB device number 2 using uhci_hcd
[ 1.562863] sd 0:0:0:0: [sda] 156368016 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 1.563029] sd 0:0:0:0: [sda] Write Protect is off
[ 1.563039] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.563110] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.585041] sr 1:0:0:0: [sr0] scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.585059] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.585773] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.589227] sda: sda1 sda2 < sda5 sda6 >
[ 1.589505] sd 0:0:1:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 1.589782] sd 0:0:1:0: [sdb] Write Protect is off
[ 1.589792] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.589861] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.597043] sdb: sdb1
[ 1.597420] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.598041] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 1.599904] sr 1:0:1:0: [sr1] scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 1.600634] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 1.627046] firewire_core 0000:00:0d.0: created device fw0: GUID 001106000000bd55, S400
[ 2.408039] random: nonblocking pool is initialized
[ 2.450352] Switched to clocksource tsc
[ 2.559002] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 3.607145] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.607271] systemd[1]: Inserted module 'ip_tables'
[ 3.680809] systemd[1]: systemd 221 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD +IDN)
[ 3.681356] systemd[1]: Detected architecture x86.
[ 3.681461] systemd[1]: No hostname configured.
[ 3.681480] systemd[1]: Set hostname to <localhost>.
[ 5.027146] systemd[1]: display-manager.service: Cannot add dependency job, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 5.029058] systemd[1]: Reached target Remote File Systems.
[ 5.029119] systemd[1]: Starting Remote File Systems.
[ 5.029260] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 5.029297] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 5.029425] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 5.029462] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 5.029495] systemd[1]: Reached target Encrypted Volumes.
[ 5.029525] systemd[1]: Starting Encrypted Volumes.
[ 5.030337] systemd[1]: Created slice Root Slice.
[ 5.030383] systemd[1]: Starting Root Slice.
[ 5.030544] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 5.030578] systemd[1]: Starting LVM2 metadata daemon socket.
[ 5.031073] systemd[1]: Created slice User and Session Slice.
[ 5.031110] systemd[1]: Starting User and Session Slice.
[ 5.031232] systemd[1]: Listening on udev Kernel Socket.
[ 5.031269] systemd[1]: Starting udev Kernel Socket.
[ 5.031416] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 5.031450] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 5.031560] systemd[1]: Listening on Journal Socket (/dev/log).
[ 5.031594] systemd[1]: Starting Journal Socket (/dev/log).
[ 5.031691] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 5.031724] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 5.031811] systemd[1]: Listening on udev Control Socket.
[ 5.031843] systemd[1]: Starting udev Control Socket.
[ 5.031979] systemd[1]: Listening on Journal Socket.
[ 5.032023] systemd[1]: Starting Journal Socket.
[ 5.032476] systemd[1]: Created slice System Slice.
[ 5.032524] systemd[1]: Starting System Slice.
[ 5.032558] systemd[1]: Reached target Slices.
[ 5.032590] systemd[1]: Starting Slices.
[ 5.054818] systemd[1]: Started Load Kernel Modules.
[ 5.055458] systemd[1]: Created slice system-getty.slice.
[ 5.055502] systemd[1]: Starting system-getty.slice.
[ 5.079212] systemd[1]: Mounting Temporary Directory...
[ 5.081810] systemd[1]: Mounting Huge Pages File System...
[ 5.088393] systemd[1]: Mounting Debug File System...
[ 5.091235] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 5.091379] systemd[1]: Mounted FUSE Control File System.
[ 5.099957] systemd[1]: Mounting POSIX Message Queue File System...
[ 5.100201] systemd[1]: Started File System Check on Root Device.
[ 5.102563] systemd[1]: Mounting Configuration File System...
[ 5.105243] systemd[1]: Starting Setup Virtual Console...
[ 5.114415] systemd[1]: Starting Apply Kernel Variables...
[ 5.114506] systemd[1]: Reached target Paths.
[ 5.114587] systemd[1]: Starting Paths.
[ 5.115316] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 5.115404] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 5.148438] systemd[1]: Starting Set Up Additional Binary Formats...
[ 5.197763] systemd[1]: Listening on Journal Audit Socket.
[ 5.200597] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 5.203059] systemd[1]: Starting Journal Service...
[ 5.214720] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 5.340254] systemd[1]: proc-sys-fs-binfmt_misc.automount: Got automount request for /proc/sys/fs/binfmt_misc, triggered by 112 (systemd-binfmt)
[ 5.342552] systemd[1]: Mounting Arbitrary Executable File Formats File System...
[ 5.537417] EXT4-fs (sda1): re-mounted. Opts: data=ordered
[ 5.541573] systemd[1]: Started Remount Root and Kernel File Systems.
[ 5.578586] systemd[1]: Started Rebuild Hardware Database.
[ 5.581027] systemd[1]: Starting udev Coldplug all Devices...
[ 5.585468] systemd[1]: Starting Load/Save Random Seed...
[ 5.586204] systemd[1]: Started First Boot Wizard.
[ 5.586419] systemd[1]: Started Create System Users.
[ 5.591360] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 5.591492] systemd[1]: Started Rebuild Dynamic Linker Cache.
[ 5.598896] systemd[1]: Mounted Configuration File System.
[ 5.599060] systemd[1]: Mounted Debug File System.
[ 5.599129] systemd[1]: Mounted Temporary Directory.
[ 5.610513] systemd[1]: Mounted Arbitrary Executable File Formats File System.
[ 5.610672] systemd[1]: Mounted Huge Pages File System.
[ 5.610784] systemd[1]: Mounted POSIX Message Queue File System.
[ 5.756195] systemd[1]: Started Apply Kernel Variables.
[ 5.813140] systemd[1]: Started Set Up Additional Binary Formats.
[ 6.021784] systemd[1]: Started udev Coldplug all Devices.
[ 6.042814] systemd[1]: Started Load/Save Random Seed.
[ 6.292132] systemd[1]: Started Create Static Device Nodes in /dev.
[ 6.295899] systemd[1]: Starting udev Kernel Device Manager...
[ 6.296059] systemd[1]: Reached target Local File Systems (Pre).
[ 6.296154] systemd[1]: Starting Local File Systems (Pre).
[ 6.296190] systemd[1]: Reached target Local File Systems.
[ 6.296226] systemd[1]: Starting Local File Systems.
[ 6.296321] systemd[1]: Started Rebuild Journal Catalog.
[ 6.296488] systemd[1]: Started Update is Completed.
[ 6.296648] systemd[1]: Started Commit a transient machine-id on disk.
[ 6.303786] systemd[1]: Mounted Virtual Machine and Container Storage.
[ 6.559625] systemd[1]: Started Setup Virtual Console.
[ 7.469898] systemd[1]: Started udev Kernel Device Manager.
[ 7.815838] systemd[1]: Started Journal Service.
[ 7.886809] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 7.886832] ACPI: Power Button [PWRB]
[ 7.887119] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 7.887127] ACPI: Power Button [PWRF]
[ 7.918275] parport_pc 00:05: reported by Plug and Play ACPI
[ 7.918363] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
[ 7.970586] systemd-journald[117]: Received request to flush runtime journal from PID 1
[ 8.273435] gameport gameport0: NS558 PnP Gameport is pnp00:09/gameport0, io 0x200, speed 1041kHz
[ 8.389020] MPU-401 device not found or device busy
[ 8.559328] Linux agpgart interface v0.103
[ 8.612901] agpgart: Detected VIA KT400/KT400A/KT600 chipset
[ 8.626143] agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
[ 8.767969] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 8.788921] NET: Registered protocol family 23
[ 8.976784] via-ircc 0000:00:11.0: can't enable device: BAR 13 [io 0xe400-0xe47f] not claimed
[ 9.257852] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
[ 9.258963] via-rhine 0000:00:12.0 eth0: VIA Rhine II at 0x1b000, 00:11:2f:e8:71:87, IRQ 23
[ 9.259754] via-rhine 0000:00:12.0 eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1
[ 9.730775] [drm] Initialized drm 1.1.0 20060810
[ 9.929165] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 9.934000] snd_via82xx 0000:00:11.5: codec_read: codec 0 is not valid [0x107e5370]
[ 9.949484] snd_via82xx 0000:00:11.5: codec_read: codec 0 is not valid [0x107e5370]
[ 9.969725] snd_via82xx 0000:00:11.5: codec_read: codec 0 is not valid [0x107e5370]
[ 9.986389] snd_via82xx 0000:00:11.5: codec_read: codec 0 is not valid [0x107e5370]
[ 10.295690] wmi: Mapper loaded
[ 10.578146] ppdev: user-space parallel port driver
[ 10.613136] via-rhine 0000:00:12.0 enp0s18: renamed from eth0
[ 10.884464] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x034200b1
[ 10.884481] nouveau [ DEVICE][0000:01:00.0] Chipset: NV34 (NV34)
[ 10.884486] nouveau [ DEVICE][0000:01:00.0] Family : NV30
[ 10.994302] nouveau [ VBIOS][0000:01:00.0] using image from PRAMIN
[ 10.994331] nouveau [ VBIOS][0000:01:00.0] BMP version 5.29
[ 10.994662] nouveau [ VBIOS][0000:01:00.0] version 04.34.20.87.00
[ 10.995737] nouveau W[ PTIMER][0000:01:00.0] unknown input clock freq
[ 10.995771] nouveau [ PFB][0000:01:00.0] RAM type: DDR1
[ 10.995777] nouveau [ PFB][0000:01:00.0] RAM size: 128 MiB
[ 10.995783] nouveau [ PFB][0000:01:00.0] ZCOMP: 0 tags
[ 11.004414] nouveau [ CLK][0000:01:00.0] --:
[ 11.004575] agpgart-via 0000:00:00.0: AGP 3.5 bridge
[ 11.004601] agpgart: systemd-udevd tried to set rate=x12. Setting to AGP3 x8 mode.
[ 11.004616] agpgart-via 0000:00:00.0: putting AGP V3 device into 8x mode
[ 11.004681] nouveau 0000:01:00.0: putting AGP V3 device into 8x mode
[ 11.004891] [TTM] Zone kernel: Available graphics memory: 443834 kiB
[ 11.004896] [TTM] Zone highmem: Available graphics memory: 644534 kiB
[ 11.004900] [TTM] Initializing pool allocator
[ 11.004919] [TTM] Initializing DMA pool allocator
[ 11.004966] nouveau [ DRM] VRAM: 127 MiB
[ 11.004972] nouveau [ DRM] GART: 64 MiB
[ 11.004980] nouveau [ DRM] BMP version 5.41
[ 11.004987] nouveau [ DRM] DCB version 2.2
[ 11.004995] nouveau [ DRM] DCB outp 00: 01000310 00009c40
[ 11.005002] nouveau [ DRM] DCB outp 01: 01010302 00000000
[ 11.005008] nouveau [ DRM] DCB outp 02: 020203f1 00000203
[ 11.005264] nouveau [ DRM] Loading NV17 power sequencing microcode
[ 11.010211] nouveau [ DRM] Saving VGA fonts
[ 11.053801] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 11.053815] [drm] Driver supports precise vblank timestamp query.
[ 11.053831] nouveau [ DRM] 0xE0DC: Parsing digital output script table
[ 11.108951] nouveau [ DRM] MM: using M2MF for buffer copies
[ 11.108995] nouveau [ DRM] Setting dpms mode 3 on TV encoder (output 2)
[ 11.166968] nouveau [ DRM] allocated 1280x1024 fb: 0x9000, bo f63d1400
[ 11.167623] fbcon: nouveaufb (fb0) is primary device
[ 11.196358] Console: switching to colour frame buffer device 160x64
[ 11.199423] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[ 11.199435] nouveau 0000:01:00.0: registered panic notifier
[ 11.210163] [drm] Initialized nouveau 1.2.1 20120801 for 0000:01:00.0 on minor 0
[ 11.281181] psmouse serio1: hgpk: ID: 10 00 64
[ 12.086852] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5
[ 12.106667] mousedev: PS/2 mouse device common for all mice
[ 95.949283] cfg80211: Calling CRDA to update world regulatory domain
[ 113.595565] fuse init (API version 7.23)
Da notare che arch l'avevo installata prima.
Dopo aver installato slack ed il suo grub, quando faccio avviare arch al secondo 12 parte un "job" di 1.30 di verifica disco che dura ogni volta 1.30 (prima dell'installazione di slack non accadeva).
Ecco invece il risultato di free di arch (dalla shell di login, prima dell'avvio di X):
Codice: Seleziona tutto
total used free shared buff/cache available
Mem: 1289068 48328 1101596 356 139144 1108788
Swap: 0 0 0
Questo invece il risultato di free dopo l'avvio di Lxde su arch:
Codice: Seleziona tutto
total used free shared buff/cache available
Mem: 1289068 116216 1006984 6316 165868 1027288
Swap: 0 0 0
Ponce, io non so forse leggere bene i dati: mi fermavo alla prima riga, dove leggendo total, used e free sembra dire che arch usa meno ram.
Comunque a me quello che interessa è sapere quale delle due distribuzioni potrebbe rendere meglio sul pc che ho intenzione di usare.
Non si tratta di quello dove ho per adesso installato e che ha generato i risultati di dmes e free che ho postato, ma del vecchio pentium III 800 Mhz con 700 Mb di RAM, di cui accennavo ad inizio post: una macchina di circa 20 anni ma che ancora regge benissimo.
Slack la ammiro per la sua solidità. In più ci sono affezionato perché è stata la prima distro su cui ho fatto esperienza di linux.
Arch la avevo già provata sul vecchio Pentium III e ci girava alla meraviglia, per l'uso d'ufficio cui è destinata a me ne bastava ed avanzava: poi, come ho accennato, dopo un aggiornamento malaccorto, il sistema si è compromesso.
In conclusione, se slack mi garantisse la stessa "leggerezza" e "velocità" (perdonami il termine atecnico ed empirico, ma non so come esprimermi diversamente) non esiterei ad installarcela perché ritengo che inconvenienti come quello appena riferito non dovrebbero accadere ed anche perché il tempo dell'installazione e della configurazione post-installazione, nel complesso è minore rispetto ad arch.
Altrimenti, mi riarmo di pazienza e ci rimetto arch.
Quello che mi gioverebbe sapere è se qualcuno di voi la risposta sa darmela in anticipo facendomi risparmiare tempo, altrimenti sperimento sul campo e pazienza...
Senza nessuna vena di polemica.
