A casa ho un modem, il D-Link 302-T griffato Alice collegato al mio Pc naturalmente tramite Ethernet. Ho provato a configurare la mia connessione Internet tramite pppoe-setup tramite i seguenti parametri, o simili (Ho trovato su internet la configurazione di pppoe che ha fatto uno, io l'ho semplicemente adattata).
Se faccio ifconfig, mi rilieva la connession point to point pp0.USER NAME
>>> Enter your PPPoE user name (default XXXXXXXXXX@aliceposta.it): xxxxxx #metto quello che mi hanno fornito quelli di alice per connettermi a Internet
INTERFACE
>>> Enter the Ethernet interface connected to the DSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default eth0): eth0
Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
>>> Enter the demand value (default no): no
DNS
Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here: server
PASSWORD
>>> Please enter your PPPoE password: xxxxxxx #io ho impostato la password che mi hanno fornito per connettermi ad internet
>>> Please re-enter your PPPoE password: xxxxxx
FIREWALLING
Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.
The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
>>> Choose a type of firewall (0-2): 0
** Summary of what you entered **
Ethernet Interface: eth0
User name: xxxxxx
Activate-on-demand: No
DNS addresses: Supplied by ISP's server
Firewalling: NONE
>>> Accept these settings and adjust configuration files (y/n)? y
Adjusting /etc/ppp/pppoe.conf
Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets
(But first backing it up to /etc/ppp/pap-secrets-bak)
(But first backing it up to /etc/ppp/chap-secrets-bak)
Congratulations, it should be all set up!
Type 'pppoe-start' to bring up your PPPoE link and 'pppoe-stop' to bring
it down. Type 'pppoe-status' to see the link status.
Poi manda il comando pppoe-start che va a buon fine:
.CONNECTED!
OK , fino a questo punto il problema non si presenta, però se tramite fluxbox entro in firefox non riesco a connettermi.
Ho pensato che non mi rilevasse i driver della scheda di rete, ma non ne sono certo.
La mia è una Etherlink 3Com 3C905B-tx-nm
Avete suggerimenti please....????
) e funziona più che bene. Delle due, o il modem è andato KO oppure un qualche problema con la scheda di rete. Riporta l'output dei comandi (eventualmente salvali su un normale file .txt se non puoi collegarti);
