Da premettere che ho un sitema raid con 3 partizioni /boot, / , /home (ed ovviamente le partizioni di swap)
Questo è mdadm.conf
Codice: Seleziona tutto
ARRAY /dev/md0 level=raid1 num-devices=2 UUID=642b0b7b:eb4bf8e8:0d287946:c85d745f
ARRAY /dev/md1 level=raid1 num-devices=2 UUID=c5b0059d:155cc525:aa8db219:7b532e03
ARRAY /dev/md2 level=raid1 num-devices=2 UUID=2c4e758c:cff38c20:5544a624:a56b3590
Ho cercato un pò di info ed ho modificato il lilo.conf come segue
Codice: Seleziona tutto
append=" vt.default_utf8=0"
disk = /dev/md0
bios = 0x80
sectors = 63
heads = 16
cylinders = 39770
partition = /dev/md1
start=63
boot = /dev/sda
bitmap = /boot/slack.bmp
bmp-colors = 255,0,255,0,255,0
bmp-table = 60,6,1,16
bmp-timer = 65,27,0,255
prompt
timeout = 1200
change-rules
reset
vga = 773
image = /boot/vmlinuz
root = /dev/md1
label = Linux
read-only
Ma al riavvio il pc si blocca.
Il problema principale sembra essere xfs (non so per quale motivo) nel "Checking root filesystem" quando esegue fsck. /dev/md1 does not exist
accedo con la pass di root, cerco di avviare xfs_repair /dev/md1 ma mi da errore "couldn't initialize XFS library"
Questo è dmesg
Codice: Seleziona tutto
PERCPU: Allocating 39452 bytes of per cpu data
NR_CPUS: 32, nr_cpu_ids: 4, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 909953
Kernel command line: BOOT_IMAGE=Linux ro root=901 vt.default_utf8=0
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PMTIMER calibration value
Detected 2999.980 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3628288k/3668864k available (6388k kernel code, 39376k reserved, 2148k data, 424k init, 2751360k highmem)
virtual kernel memory layout:
fixmap : 0xffe19000 - 0xfffff000 (1944 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0963000 - 0xc09cd000 ( 424 kB)
.data : 0xc073d137 - 0xc0956278 (2148 kB)
.text : 0xc0100000 - 0xc073d137 (6388 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency.. 5999.96 BogoMIPS (lpj=11999920)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080609
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5999.96 BogoMIPS (lpj=11999923)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (11999.92 BogoMIPS).
net_namespace: 776 bytes
xor: automatically using best checksumming function: pIII_sse
pIII_sse : 10395.000 MB/sec
xor: using function: pIII_sse (10395.000 MB/sec)
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
PCI: MCFG area at f0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
PCI: 0000:00:1a.0 reg 20 io port: [d100, d11f]
PCI: 0000:00:1a.1 reg 20 io port: [d200, d21f]
PCI: 0000:00:1a.2 reg 20 io port: [d000, d01f]
PCI: 0000:00:1a.7 reg 10 32bit mmio: [fa205000, fa2053ff]
PCI: 0000:00:1b.0 reg 10 64bit mmio: [fa200000, fa203fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
PCI: 0000:00:1d.0 reg 20 io port: [d300, d31f]
PCI: 0000:00:1d.1 reg 20 io port: [d400, d41f]
PCI: 0000:00:1d.2 reg 20 io port: [d500, d51f]
PCI: 0000:00:1d.7 reg 10 32bit mmio: [fa204000, fa2043ff]
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: 0000:00:1f.2 reg 10 io port: [d600, d607]
PCI: 0000:00:1f.2 reg 14 io port: [d700, d703]
PCI: 0000:00:1f.2 reg 18 io port: [d800, d807]
PCI: 0000:00:1f.2 reg 1c io port: [d900, d903]
PCI: 0000:00:1f.2 reg 20 io port: [da00, da0f]
PCI: 0000:00:1f.2 reg 24 io port: [db00, db0f]
PCI: 0000:00:1f.3 reg 10 64bit mmio: [fa206000, fa2060ff]
PCI: 0000:00:1f.3 reg 20 io port: [500, 51f]
PCI: 0000:00:1f.5 reg 10 io port: [dd00, dd07]
PCI: 0000:00:1f.5 reg 14 io port: [de00, de03]
PCI: 0000:00:1f.5 reg 18 io port: [df00, df07]
PCI: 0000:00:1f.5 reg 1c io port: [e000, e003]
PCI: 0000:00:1f.5 reg 20 io port: [e100, e10f]
PCI: 0000:00:1f.5 reg 24 io port: [e200, e20f]
PCI: 0000:01:00.0 reg 10 32bit mmio: [f6000000, f6ffffff]
PCI: 0000:01:00.0 reg 14 64bit mmio: [e0000000, efffffff]
PCI: 0000:01:00.0 reg 1c 64bit mmio: [f4000000, f5ffffff]
PCI: 0000:01:00.0 reg 24 io port: [a000, a07f]
PCI: 0000:01:00.0 reg 30 32bit mmio: [0, 1ffff]
PCI: bridge 0000:00:01.0 io port: [a000, afff]
PCI: bridge 0000:00:01.0 32bit mmio: [f4000000, f7ffffff]
PCI: bridge 0000:00:01.0 64bit mmio pref: [e0000000, efffffff]
PCI: bridge 0000:00:1c.0 io port: [9000, 9fff]
PCI: 0000:03:00.0 reg 24 32bit mmio: [fa000000, fa001fff]
pci 0000:03:00.0: PME# supported from D3hot
pci 0000:03:00.0: PME# disabled
PCI: 0000:03:00.1 reg 10 io port: [b000, b007]
PCI: 0000:03:00.1 reg 14 io port: [b100, b103]
PCI: 0000:03:00.1 reg 18 io port: [b200, b207]
PCI: 0000:03:00.1 reg 1c io port: [b300, b303]
PCI: 0000:03:00.1 reg 20 io port: [b400, b40f]
PCI: bridge 0000:00:1c.4 io port: [b000, bfff]
PCI: bridge 0000:00:1c.4 32bit mmio: [fa000000, fa0fffff]
PCI: 0000:04:00.0 reg 10 io port: [c000, c0ff]
PCI: 0000:04:00.0 reg 18 64bit mmio: [f9000000, f9000fff]
PCI: 0000:04:00.0 reg 30 32bit mmio: [0, ffff]
pci 0000:04:00.0: supports D1
pci 0000:04:00.0: supports D2
pci 0000:04:00.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:04:00.0: PME# disabled
PCI: bridge 0000:00:1c.5 io port: [c000, cfff]
PCI: bridge 0000:00:1c.5 32bit mmio: [f8000000, f9ffffff]
PCI: 0000:05:06.0 reg 10 32bit mmio: [fa104000, fa1047ff]
PCI: 0000:05:06.0 reg 14 32bit mmio: [fa100000, fa103fff]
pci 0000:05:06.0: supports D1
pci 0000:05:06.0: supports D2
pci 0000:05:06.0: PME# supported from D0 D1 D2 D3hot
pci 0000:05:06.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
PCI: bridge 0000:00:1e.0 32bit mmio: [fa100000, fa1fffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
tracer: 772 pages allocated for 65536 entries of 48 bytes
actual entries 65620
ACPI: RTC can wake from S4
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x290-0x29f has been reserved
system 00:01: ioport range 0x800-0x87f has been reserved
system 00:01: ioport range 0x290-0x294 has been reserved
system 00:01: ioport range 0x880-0x88f has been reserved
system 00:0b: ioport range 0x400-0x4bf could not be reserved
system 00:0c: iomem range 0xf0000000-0xf3ffffff could not be reserved
system 00:0d: iomem range 0xd3000-0xd3fff has been reserved
system 00:0d: iomem range 0xf0000-0xf7fff could not be reserved
system 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
system 00:0d: iomem range 0xfc000-0xfffff could not be reserved
system 00:0d: iomem range 0xdfee0000-0xdfefffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0x100000-0xdfedffff could not be reserved
system 00:0d: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0d: iomem range 0xfed10000-0xfed1dfff could not be reserved
system 00:0d: iomem range 0xfed20000-0xfed8ffff could not be reserved
system 00:0d: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0d: iomem range 0xffb00000-0xffb7ffff could not be reserved
system 00:0d: iomem range 0xfff00000-0xffffffff could not be reserved
system 00:0d: iomem range 0xe0000-0xeffff has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0xa000-0xafff
pci 0000:00:01.0: MEM window: 0xf4000000-0xf7ffffff
pci 0000:00:01.0: PREFETCH window: 0x000000e0000000-0x000000efffffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0: IO window: 0x9000-0x9fff
pci 0000:00:1c.0: MEM window: disabled
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.4: IO window: 0xb000-0xbfff
pci 0000:00:1c.4: MEM window: 0xfa000000-0xfa0fffff
pci 0000:00:1c.4: PREFETCH window: disabled
pci 0000:00:1c.5: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.5: IO window: 0xc000-0xcfff
pci 0000:00:1c.5: MEM window: 0xf8000000-0xf9ffffff
pci 0000:00:1c.5: PREFETCH window: 0x000000fa300000-0x000000fa3fffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: 0xfa100000-0xfa1fffff
pci 0000:00:1e.0: PREFETCH window: disabled
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.5: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffff]
bus: 01 index 0 io port: [a000, afff]
bus: 01 index 1 mmio: [f4000000, f7ffffff]
bus: 01 index 2 mmio: [e0000000, efffffff]
bus: 01 index 3 mmio: [0, 0]
bus: 02 index 0 io port: [9000, 9fff]
bus: 02 index 1 mmio: [0, 0]
bus: 02 index 2 mmio: [0, 0]
bus: 02 index 3 mmio: [0, 0]
bus: 03 index 0 io port: [b000, bfff]
bus: 03 index 1 mmio: [fa000000, fa0fffff]
bus: 03 index 2 mmio: [0, 0]
bus: 03 index 3 mmio: [0, 0]
bus: 04 index 0 io port: [c000, cfff]
bus: 04 index 1 mmio: [f8000000, f9ffffff]
bus: 04 index 2 mmio: [fa300000, fa3fffff]
bus: 04 index 3 mmio: [0, 0]
bus: 05 index 0 mmio: [0, 0]
bus: 05 index 1 mmio: [fa100000, fa1fffff]
bus: 05 index 2 mmio: [0, 0]
bus: 05 index 3 io port: [0, ffff]
bus: 05 index 4 mmio: [0, ffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.29 [Flags: R/W].
JFS: nTxBlock = 8192, nTxLock = 65536
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
GFS2 (built Nov 20 2008 22:30:39) installed
msgmni has been set to 1714
async_tx: api initialized (async)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pci_express 0000:00:01.0:pcie00: allocate port service
pci_express 0000:00:01.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pci_express 0000:00:1c.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.4: setting latency timer to 64
pcieport-driver 0000:00:1c.4: found MSI capability
pci_express 0000:00:1c.4:pcie00: allocate port service
pci_express 0000:00:1c.4:pcie02: allocate port service
pci_express 0000:00:1c.4:pcie03: allocate port service
pcieport-driver 0000:00:1c.5: setting latency timer to 64
pcieport-driver 0000:00:1c.5: found MSI capability
pci_express 0000:00:1c.5:pcie00: allocate port service
pci_express 0000:00:1c.5:pcie02: allocate port service
pci_express 0000:00:1c.5:pcie03: allocate port service
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: framebuffer at 0xf5000000, mapped to 0xf8d00000, using 1536k, total 14336k
vesafb: mode is 1024x768x8, linelength=1024, pages=3
vesafb: protected mode interface info at c000:b430
vesafb: pmi: set display start = c00cb493, set palette = c00cb4ee
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
floppy0: no floppy controllers found
brd: module loaded
loop: module loaded
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.20)
input: Macintosh mouse button emulation as /devices/virtual/input/input0
Uniform Multi-Platform E-IDE driver
jmicron 0000:03:00.1: IDE controller (0x197b:0x2363 rev 0x02)
pci 0000:03:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
jmicron 0000:03:00.1: 100% native mode on irq 17
ide0: BM-DMA at 0xb400-0xb407
ide1: BM-DMA at 0xb408-0xb40f
Probing IDE interface ide0...
hda: LG DVD-ROM DRD-8120B, ATAPI CD/DVD-ROM drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
Probing IDE interface ide1...
ide0 at 0xb000-0xb007,0xb102 on irq 17
ide1 at 0xb200-0xb207,0xb302 on irq 17
hda: ATAPI 40X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 1.00
Loading iSCSI transport class v2.0-870.
rdac: device handler registered
hp_sw: device handler registered
emc: device handler registered
alua: device handler registered
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver 1.1-5[2456]-ms
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
scsi: <fdomain> Detection failed (no card)
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver: 8.02.01-k7
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.2.7
Copyright(c) 2004-2008 Emulex. All rights reserved.
Failed initialization of WD-7000 SCSI card!
DC390: clustering now enabled by default. If you get problems load
with "disable_clustering=1" and report to maintainers
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008
GDT-HA: Storage RAID Controller Driver. Version: 3.05
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.011.
nsp32: loading...
ipr: IBM Power RAID SCSI Device Driver version: 2.4.1 (April 24, 2007)
RocketRAID 3xxx/4xxx Controller driver v1.3 (071203)
stex: Promise SuperTrak EX Driver version: 3.6.0000.1
st: Version 20080504, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:03:00.0: version 3.0
ahci 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part
ahci 0000:03:00.0: setting latency timer to 64
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m8192@0xfa000000 port 0xfa000100 irq 16
ata2: SATA max UDMA/133 abar m8192@0xfa000000 port 0xfa000180 irq 16
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi4 : ata_piix
scsi5 : ata_piix
ata3: SATA max UDMA/133 cmd 0xd600 ctl 0xd700 bmdma 0xda00 irq 19
ata4: SATA max UDMA/133 cmd 0xd800 ctl 0xd900 bmdma 0xda08 irq 19
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: HPA detected: current 976771055, native 976773168
ata3.00: ATA-8: ST3500320AS, SD81, max UDMA/133
ata3.00: 976771055 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-8: ST3500320AS, SD81, max UDMA/133
ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata4.01: ATAPI: PIONEER DVD-RW DVR-216D, 1.03, max UDMA/66
ata4.00: configured for UDMA/133
ata4.01: configured for UDMA/66
scsi 4:0:0:0: Direct-Access ATA ST3500320AS SD81 PQ: 0 ANSI: 5
sd 4:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 4:0:0:0: [sda] Attached SCSI disk
scsi 5:0:0:0: Direct-Access ATA ST3500320AS SD81 PQ: 0 ANSI: 5
sd 5:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4
sd 5:0:0:0: [sdb] Attached SCSI disk
scsi 5:0:1:0: CD-ROM PIONEER DVD-RW DVR-216D 1.03 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
sr 5:0:1:0: Attached scsi CD-ROM sr0
ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
ata_piix 0000:00:1f.5: setting latency timer to 64
scsi6 : ata_piix
scsi7 : ata_piix
ata5: SATA max UDMA/133 cmd 0xdd00 ctl 0xde00 bmdma 0xe100 irq 19
ata6: SATA max UDMA/133 cmd 0xdf00 ctl 0xe000 bmdma 0xe108 irq 19
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
scsi8 : pata_legacy
ata7: PATA max PIO4 cmd 0x1f0 ctl 0x3f6 irq 14
scsi9 : pata_legacy
ata8: PATA max PIO4 cmd 0x170 ctl 0x376 irq 15
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
Fusion MPT FC Host driver 3.04.07
Fusion MPT SAS Host driver 3.04.07
ohci1394 0000:05:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[fa104000-fa1047ff] Max Packet=[2048] IR/IT contexts=[4/8]
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfa205000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27.7-smp ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfa204000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27.7-smp ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000d100
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-5: new high speed USB device using ehci_hcd and address 2
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27.7-smp uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000d200
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-5: configuration #1 chosen from 1 choice
usb 2-5: New USB device found, idVendor=0781, idProduct=5151
usb 2-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-5: Product: Cruzer Micro
usb 2-5: Manufacturer: SanDisk
usb 2-5: SerialNumber: 0774021D6BC202EF
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27.7-smp uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1a.2: setting latency timer to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000d000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27.7-smp uhci_hcd
usb usb5: SerialNumber: 0000:00:1a.2
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d300
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.27.7-smp uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.0
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d400
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.27.7-smp uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.1
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d500
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb8: Product: UHCI Host Controller
usb usb8: Manufacturer: Linux 2.6.27.7-smp uhci_hcd
usb usb8: SerialNumber: 0000:00:1d.2
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
scsi10 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1 1057 MB/s
raid6: int32x2 985 MB/s
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000fcd0200001d7d]
raid6: int32x4 807 MB/s
raid6: int32x8 765 MB/s
raid6: mmxx1 3521 MB/s
raid6: mmxx2 4070 MB/s
raid6: sse1x1 2468 MB/s
raid6: sse1x2 3186 MB/s
raid6: sse2x1 4623 MB/s
raid6: sse2x2 5248 MB/s
raid6: using algorithm sse2x2 (5248 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Using IPI No-Shortcut mode
md: Autodetecting RAID arrays.
md: Scanned 6 and added 6 devices.
md: autorun ...
md: considering sdb4 ...
md: adding sdb4 ...
md: sdb3 has different UUID to sdb4
md: sdb1 has different UUID to sdb4
md: adding sda4 ...
md: sda3 has different UUID to sdb4
md: sda1 has different UUID to sdb4
md: created md2
md: bind<sda4>
md: bind<sdb4>
md: running: <sdb4><sda4>
raid1: raid set md2 active with 2 out of 2 mirrors
md: considering sdb3 ...
md: adding sdb3 ...
md: sdb1 has different UUID to sdb3
md: adding sda3 ...
md: sda1 has different UUID to sdb3
md: created md1
md: bind<sda3>
md: bind<sdb3>
md: running: <sdb3><sda3>
md: md1: raid array is not clean -- starting background reconstruction
raid1: raid set md1 active with 2 out of 2 mirrors
md: considering sdb1 ...
md: resync of RAID array md1
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
md: using 128k window, over a total of 341798848 blocks.
md: resuming resync of md1 from checkpoint.
md: adding sdb1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: running: <sdb1><sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
UDF-fs: No VRS found
XFS mounting filesystem md1
Starting XFS recovery on filesystem: md1 (logdev: internal)
Ending XFS recovery on filesystem: md1 (logdev: internal)
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 424k freed
fuse init (API version 7.9)
Non ci sono perdite di dati (almeno così sembra...)
Qualche idea su come risolvere??? non vorrei dover riformattare tutto......
Grazie in anticipo
:cf
