Moderatore: Staff
Codice: Seleziona tutto
#!/bin/sh
# Slackbuild Creator v 0.2
# Written by Savino Pio Liguori aka jimmy_page_89
# Contact: jimmy_page_89 AT hotmail DOT it
# This script create a Slackbuild, following the standards of the
# Slacky.eu community ( http:www.slacky.eu )
# Actual standard: 13.37
# Redistribution and use of this script, with or without modification, is
# permitted provided that the following conditions are met:
#
# 1. Redistributions of this script must retain the above copyright
# notice, this list of conditions and the following disclaimer.
#
# THIS SOFTWARE IS PROVIDED BY THE AUTHOR ''AS IS'' AND ANY EXPRESS OR IMPLIED
# WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
# MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
# EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
# PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
# OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
# WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
# OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
# ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
WORKDIR=${$WORKDIR:-$HOME}
FAVEDITOR=${$FAVEDITOR:-vim}
SLACKYSTD=${$SLACKYSTD:-YES}
set -e
# Defining functions
_print_slackbuild()
{
# Creating slacky tree
mkdir -p $WORKDIR/$NAME/$VER/src
cat > $WORKDIR/$NAME/$VER/src/$NAME.SlackBuild << EOF
#!/bin/sh
# Heavily based on the Slackware 13.37 SlackBuild (v1)
# Written by $AUTH ( $AUTHMAIL )
# Last build from $BUILDER ( $BUILDMAIL )
# Slackware build script for $NAME
# Official Site: $SITE
# Redistribution and use of this script, with or without modification, is
# permitted provided that the following conditions are met:
#
# 1. Redistributions of this script must retain the above copyright
# notice, this list of conditions and the following disclaimer.
#
# THIS SOFTWARE IS PROVIDED BY THE AUTHOR ''AS IS'' AND ANY EXPRESS OR IMPLIED
# WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
# MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
# EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
# PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
# OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
# WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
# OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
# ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
set -e
PKGNAME=$NAME
VERSION=\${VERSION:-$VER}
BUILD=\${BUILD:-$BUILD}
TAG=\${TAG:-sl}
ARCH=\${ARCH:-$ARCH}
SOURCE="$SRC"
TAR=$TAR
DIR=$DIR
# If EULA
if [ -e EULA.TXT ];then
more EULA.TXT
echo "Do you accept terms? (yes/[no])"
read ACCEPT
if [ "\$ACCEPT" != "yes" ];then
echo; echo "SlackBuild Aborted!!"
exit 1
fi
fi
# Does not touch following if not needed
CWD=\$(pwd)
TMP=\${TMP:-/tmp/buildpkgs/\$PKGNAME}
PKG=\$TMP/package-\$PKGNAME
OUTPUT=\${OUTPUT:-\$CWD}
TAR=\${TAR:-\$(basename \$SOURCE)}
DIR=\${DIR:-\$(echo "\$TAR"|sed -r 's/(\.tar|)(.gz|.bz2|)$//')}
if [ ! -e \$CWD/\$TAR ];then
wget \$SOURCE
fi
CHOST="i486"
if [ "\$ARCH" = "i486" ]; then
SLKCFLAGS="-O2 -march=i486 -mtune=i686"
LIBDIRSUFFIX=""
elif [ "\$ARCH" = "i586" ]; then
SLKCFLAGS="-O2 -march=i586 -mtune=i686"
LIBDIRSUFFIX=""
elif [ "\$ARCH" = "i686" ]; then
SLKCFLAGS="-O2 -march=i686 -mtune=i686"
LIBDIRSUFFIX=""
elif [ "\$ARCH" = "x86_64" ]; then
SLKCFLAGS="-O2 -fPIC"
LIBDIRSUFFIX="64"
CHOST="x86_64"
fi
rm -rf \$TMP
mkdir -p \$TMP \$PKG \$OUTPUT
cd \$TMP
tar xvf \$CWD/\$TAR
cd \$DIR
$PATCH
chown -R root:root .
chmod -R u+w,go+r-w,a-s .
$MAKE
$SPECIAL
mkdir -p \$PKG/usr/doc/\$PKGNAME-\$VERSION
cp -r \\
$DOC \\
\$PKG/usr/doc/\$PKGNAME-\$VERSION
cat \$CWD/\$PKGNAME.SlackBuild > \$PKG/usr/doc/\$PKGNAME-\$VERSION/\$PKGNAME.SlackBuild
cat \$CWD/slack-desc > \$PKG/usr/doc/\$PKGNAME-\$VERSION/slack-desc
if [ -d \$PKG/usr/man ]; then
( cd \$PKG/usr/man
find . -type f -exec gzip -9 {} \;
for i in \$( find . -type l ) ; do ln -s \$( readlink \$i ).gz \$i.gz ; rm \$i ; done
)
fi
( cd \$PKG
find . | xargs file | grep "executable" | grep ELF | cut -f 1 -d : | xargs -r strip --strip-unneeded 2> /dev/null || true
find . | xargs file | grep "shared object" | grep ELF | cut -f 1 -d : | xargs -r strip --strip-unneeded 2> /dev/null || true
find . | xargs file | grep "current ar archive" | cut -f 1 -d : | xargs -r strip --strip-unneeded 2> /dev/null || true
)
mkdir -p \$PKG/install
cat \$CWD/slack-desc > \$PKG/install/slack-desc
[ -e \$CWD/doinst.sh ] && cat \$CWD/doinst.sh > \$PKG/install/doinst.sh
cd \$PKG
chown -R root:root \$PKG
if [ -x "\$(which requiredbuilder 2>/dev/null)" ];then
requiredbuilder -y -v -s $SHAREBIN \$CWD \$PKG
fi
/sbin/makepkg -l y -c n \$OUTPUT/\$PKGNAME-\$VERSION-\$ARCH-\$BUILD\$TAG.\${PKGTYPE:-txz}
if [ "\$1" = "--cleanup" ]; then
rm -rf \$TMP
fi
EOF
}
_print_std_doinst()
{
cat > $WORKDIR/$NAME/$VER/src/doinst.sh << EOF
config() {
NEW="\$1"
OLD="\$(dirname \$NEW)/\$(basename \$NEW .new)"
# If there's no config file by that name, mv it over:
if [ ! -r \$OLD ]; then
mv \$NEW \$OLD
elif [ "\$(cat \$OLD | md5sum)" = "\$(cat \$NEW | md5sum)" ]; then
# toss the redundant copy
rm \$NEW
fi
# Otherwise, we leave the .new copy for the admin to consider...
}
#if [ -e etc/rc.d/rc.script ]; then
# cp -a etc/rc.d/rc.script etc/rc.d/rc.script.new.incoming
# cat etc/rc.d/rc.script.new > etc/rc.d/rc.script.new.incoming
# mv etc/rc.d/rc.script.new.incoming etc/rc.d/rc.script.new
#fi
#config etc/rc.d/rc.script.new
#config etc/configfile.new
EOF
$FAVEDITOR $WORKDIR/$NAME/$VER/src/doinst.sh
}
_print_slackdesc()
{
# This script was "inspired" from the original slack-desc script
# by naitso. You can find the original at this page:
# http://www.slacky.eu/wikislack/index.php?title=Crea_file_slack-desc
local COUNT=0
local R0
local R1
local R2
# Set file name
local FILE=$WORKDIR/$NAME/$VER/src/slack-desc
clear
# Check if slack-desc alredy exist in your work directory
if [ -e $FILE ]; then
while [ $COUNT == 0 ]; do
clear
echo "slack-desc on $WORKDIR alredy exist! Overwrite?"
echo "Type Y/N or Q to quit"
read R0
case "$R0" in
n | N )
echo "This slack-desc become slack-desc.new"
FILE=$FILE.new
COUNT=1
;;
y | Y )
rm $WORKDIR/$FILE || exit 2
COUNT=1
;;
q | Q )
echo "Quit"
exit 0
;;
* ) clear
echo "Please enter only Y, N or Q to quit"
sleep 2
esac
done
fi
# First question
echo ""
echo "Write a very short package's description and press ENTER"
echo "(ex: Free FTP client)"
echo ""
read R1
# Second question
echo ""
echo "Write a package description and press ENTER"
echo "(ascii only no fancy character: a-z and - or _)"
echo ""
read R2
#build slack-desc
local NUM=0
local SPACE=$(echo "$NAME" | sed -e "s/./ /g")
local RULER="|----handy-ruler----"
local N_RULER=$(echo -n "$RULER" | wc -m)
local CHA=$(echo -n "$NAME" | wc -m)
# Set the max row for description
local MAX_ROW=7
# limit the columns
local COL=$[77-$CHA]
if [ $CHA -gt "40" ]; then
echo "Name too long, please change it"
exit 1
fi
while [ $N_RULER -lt $[$COL+1] ]; do
LINE=$LINE$(echo -n "-")
N_RULER=$[N_RULER+1]
done
# Slack-desc header
cat > $FILE << EOF
# HOW TO EDIT THIS FILE:
# The "handy ruler" below makes it easier to edit a package description. Line
# up the first '|' above the ':' following the base package name, and the '|'
# on the right side marks the last column you can put a character in. You must
# make exactly 11 lines for the formatting to be correct. It's also customary
# to leave one space after the ':'.
$SPACE$RULER$LINE|
EOF
# limit description for slack-desc
local ROW=$(echo $R2 | fmt -w $COL | sed -e "s/^/$NAME: &/ " | wc -l)
if [ $ROW -ge "$MAX_ROW" ]; then
ROW=$MAX_ROW
fi
local MAX=$[$MAX_ROW-$ROW]
# Adding package-name and short description to file, (all in one line)
echo "$NAME ($R1)" | fmt -w $COL | sed -n -e "1,1s/^/$NAME: &/p " >> $FILE
# Adding a empty row
echo $NAME: >> $FILE
# Adding the description in max 7 rows
echo $R2 | fmt -w $COL | sed -n -e "1,7s/^/$NAME: &/p " >> $FILE
# Adding a empty row before homepage
echo $NAME: >> $FILE
# If the rows are minus than 11, add the remaining (empty)
while [ $NUM -lt $MAX ]; do
echo "$NAME:" >> $FILE
NUM=$[NUM+1]
done
}
_download()
{
local URL
read -p "Insert your URL: " URL
wget $URL
mv $(basename $URL) $WORKDIR/$NAME/$VER/src/
}
_define_name()
{
local END=n
while [ "$END" = "n" ]; do
read -p "Package name: " NAME
read -p "$NAME - OK, No(n)" END
if [ -z "$NAME" ]; then
echo "Empty name!"
END=n
fi
done
}
_define_official_site()
{
local END=n
while [ "$END" = "n" ]; do
read -p "Official site: " SITE
read -p "$SITE - OK, No(n)" END
if [ -z "$SITE" ]; then
echo "Empty site!"
END=n
fi
done
}
_define_author()
{
local END=n
while [ "$END" = "n" ]; do
read -p "Author: " AUTH
read -p "Contact: " AUTHMAIL
read -p "$AUTH ( $AUTHMAIL ) - OK, No(n)" END
if [ -z "$AUTH" -o -z "$AUTHMAIL" ]; then
if [ "$END" != "n" ]; then
echo "Empty tags!"
END=n
fi
fi
done
}
_define_builder()
{
local END=n
while [ "$END" = "n" ]; do
read -p "Last builder: " BUILDER
read -p "Contact: " BUILDMAIL
read -p "$BUILDER ( $BUILDMAIL ) - OK, No(n)" END
if [ -z "$BUILDER" -o -z "$BUILDMAIL" ]; then
if [ "$END" != "n" ]; then
echo "Empty tags!"
END=n
fi
fi
done
}
_define_version()
{
local END=n
while [ "$END" = "n" ]; do
read -p "Package version: " VER
read -p "$VER - OK, No(n)" END
if [ -z "$VER" ]; then
echo "Empty tag!"
END=n
fi
done
}
_set_build()
{
local END=n
while [ "$END" = "n" ]; do
read -p "Package build (Enter if 1) :" BUILD
if [ -z "$BUILD" ]; then
BUILD=1
fi
read -p "$BUILD - OK, No(n)" END
done
}
_define_arch()
{
local END=n
while [ "$END" = "n" ]; do
echo "Please select architecture:"
echo " 1) i486"
echo " 2) i686"
echo " 3) x86_64"
echo " 4) noarch"
echo " 5) host (same as uname -m): "
read ARCH
if [ "$ARCH" = "1" ]; then
ARCH="i486"
elif [ "$ARCH" = "2" ]; then
ARCH="i686"
elif [ "$ARCH" = "3" ]; then
ARCH="x86_64"
elif [ "$ARCH" = "4" ]; then
ARCH="noarch"
elif [ "$ARCH" = "5" ]; then
ARCH=$(uname -m)
else
echo "Wrong option!"
ARCH=""
fi
if [ ! -z "$ARCH" ]; then
read -p "$ARCH - OK, No(n)" END
fi
done
}
_define_source_url()
{
local END=n
while [ "$END" = "n" ]; do
read -p "Source URL (Press Enter if not): " SRC
echo "$SRC"
read -p "OK, No(n)" END
done
if [ ! -z "$SRC" ]; then
SRC=$(echo $SRC | sed -e 's/'$VER'/$VERSION/') # Change the number version with the tag $VERSION
# -e 's/'$NAME'/$PKGNAME/' COME FUNZIONARE?
fi
}
_set_tarball_name()
{
local END=n
while [ "$END" = "n" ]; do
read -p "Tarball name (if not standard): " TAR
if [ ! -z "$TAR" ]; then
read -p "$TAR -OK, No(n)" END
else
END=""
fi
done
if [ ! -z "$TAR" ]; then
TAR=$(echo $TAR | sed -e 's/'$NAME'/$PKGNAME/' \
-e 's/'$VER'/$VERSION/') # DA TESTARE
fi
}
_set_dir_name()
{
local END=n
while [ "$END" = "n" ]; do
read -p "Source directory (if not standard): " DIR
if [ ! -z "$DIR" ]; then
read -p "$DIR - OK, No(n)" END
else
END=""
fi
done
}
_write_patch()
{
local END=n
if [ -e "$WORKDIR/patch.tmp" ]; then
rm $WORKDIR/patch.tmp
fi
while [ "$END" = "n" ]; do
echo "Patch section"
echo "Now this script is going to open $FAVEDITOR where"
echo "you have to write the entire command of the patch(es)."
echo "Simply don't save if there aren't patches."
echo "(Don't forget the CWD variable!)"
read
$FAVEDITOR $WORKDIR/patch.tmp
if [ -e "$WORKDIR/patch.tmp" ]; then
PATCH=$(cat $WORKDIR/patch.tmp)
echo "$PATCH"
read -p "OK, No(n)" END
else
END=""
fi
done
if [ -e "$WORKDIR/patch.tmp" ]; then
rm $WORKDIR/patch.tmp
fi
}
_set_build_type()
{
local END=n
local BUTYPE
while [ "$END" = "n" ]; do
echo "What type of build have this package?"
echo " 1) configure"
echo " 2) cmake"
echo " 3) python"
echo " *) custom"
read BUTYPE
case "$BUTYPE" in
1)
_std_conf
;;
2)
_cmake_conf
;;
3)
_py_conf
;;
*)
$FAVEDITOR $WORKDIR/build.tmp
esac
MAKE=`cat $WORKDIR/build.tmp`
echo ""
read -p "It's all ok? OK, No(n)" END
rm $WORKDIR/build.tmp
done
}
_write_special_op()
{
local END=n
if [ -e "$WORKDIR/special.tmp" ]; then
rm $CWD/special.tmp
fi
while [ "$END" = "n" ]; do
echo "Special operations section"
echo "Now this script is going to open $FAVEDITOR where"
echo "you have to write special operations."
echo "Simply don't save if there isn't nothing to do."
read
$FAVEDITOR $WORKDIR/special.tmp
if [ -e "$WORKDIR/special.tmp" ]; then
SPECIAL=$(cat $WORKDIR/special.tmp)
echo "$SPECIAL"
read -p "OK, No(n)" END
else
END=""
fi
done
if [ -e "$WORKDIR/special.tmp" ]; then
rm $WORKDIR/special.tmp
fi
}
_select_docs()
{
local END=n
while [ "$END" = "n" ]; do
read -p "Insert documentation file names: " DOC
if [ -z "$DOC" ]; then
echo "Empty tag!"
else
read -p "$DOC - OK, No(n)" END
fi
done
}
_sharebin()
{
local END=n
while [ "$END" = "n" ]; do
read -p "Do you have some binaries in /usr/share? ok(y), NO " SHAREBIN
if [ -z "$SHAREBIN" ]; then
read -p "There aren't. OK, No(n)" END
else
read -p "There are. OK, No(n)" END
SHAREBIN="-c -b"
fi
done
}
_std_conf()
{
cat > $WORKDIR/build.tmp << EOF
CFLAGS="\$SLKCFLAGS" \\
CXXFLAGS="\$SLKCFLAGS" \\
./configure \\
--prefix=/usr \\
--libdir=/usr/lib\$LIBDIRSUFFIX \\
--sysconfdir=/etc \\
--localstatedir=/var \\
--mandir=/usr/man \\
--build=\$CHOST-slackware-linux
make
make install DESTDIR=\$PKG
EOF
$FAVEDITOR $WORKDIR/build.tmp
}
_cmake_conf()
{
cat > $WORKDIR/build.tmp << EOF
( mkdir -p build
cd build
cmake .. \
-DCMAKE_C_FLAGS:STRING="\$SLKCFLAGS" \\
-DCMAKE_CXX_FLAGS:STRING="\$SLKCFLAGS" \\
-DCMAKE_INSTALL_PREFIX=/usr \\
-DMAN_INSTALL_DIR=/usr/man \\
-DSYSCONF_INSTALL_DIR=/etc \\
-DLIB_SUFFIX=\${LIBDIRSUFFIX}
make
make install DESTDIR=\$PKG
)
EOF
$FAVEDITOR $WORKDIR/build.tmp
}
_py_conf()
{
cat > $WORKDIR/build.tmp << EOF
python setup.py install --root=\$PKG
EOF
$FAVEDITOR $WORKDIR/build.tmp
}
_slack_desc()
{
local DSK
echo "What do you want to do with slack-desc?"
echo " 1) Create"
echo " 2) Download"
echo " *) I do not want it, i'm a Pidgey"
read DSK
case "$DSK" in
1)
_print_slackdesc
;;
2)
_down_files
;;
*)
echo "Please supports fat pidgeons."
;;
esac
}
_doinst()
{
local OPT
clear
echo "What do you want to do with doinst.sh?"
echo " 1) Create"
echo " 2) Create from Slacky Standard"
echo " 3) Download"
echo " *) I don't need it."
read OPT
case "$OPT" in
1)
$FAVEDITOR $WORKDIR/$NAME/$VERSION/src/doinst.sh
;;
2)
_print_std_doinst
;;
3)
_download
;;
*)
echo "KTHXBAI"
;;
esac
}
# Now the real script starts
echo "SlackBuild Creator"
# Package name
_define_name
# Official site
_define_official_site
# Author
_define_author
# Packager
_define_builder
# Version
_define_version
# Number of build
_set_build
# Architecture
_define_arch
# Source URL
_define_source_url
# Tarball name
_define_tarball_name
# Sources dir
_set_dir_name
# Patches
_write_patch
# Configure, cmake or other?
_set_build_type
# Special operations
_write_special_op
# Documentation
_select_docs
# Binaries in /usr/share
_sharebin
# Now let's go!!!
echo "Ok, all data insert. Press Enter to create $NAME.Slackbuild in $WORKDIR/$NAME/$VER/src"
read
_print_slackbuild # print..print...print..
_doinst # doinst.sh
_slack_desc # Slack-desc choises
echo "Ok, that's all folks. Thanks a lot for using Slackbuild Creator! ^TM"
exit 0Codice: Seleziona tutto
CHANGELOG
0.2
- Changed default workdir
* Now is set to $HOME by default
- Fixed global variables
* Now you can determine they externally
- Inverted _build_type() and _special()
- Added SLACKYSTD
* Set NO if you don't want Slacky.eu standard
(WARNING: not implemented yet)
- In function _std_doinst()
* Renamed in _print_std_doinst
- In function _down_files()
* Renamed in _download (c'est plus facile)
* Fixed "mv" section to move every file you want
- In function _name()
* Renamed in _define_name()
- In function _official()
* Renamed in _define_official_site()
- In function _auth()
* Renamed in _define_author()
- In function _builder()
* Renamed in _define_builder()
- In function _arch()
* Renamed in _define_arch()
- In function _source()
* Renamed in _define_source_url()
- In function _tarball()
* Renamed in _set_tarball_name()
- In function _dir()
* Renamed in _set_dir_name()
- In function _patch()
* Renamed in _write_patch()
* Fix "rm" section
- In function _build_type()
* Renamed in _set_build_type()
- In function _special()
* Renamed in _write_special_op()
- In function _doc()
* Renamed in _select_docs
-
0.1
- First release
Codice: Seleziona tutto
# Slacky.eu community ( http://www.slacky.eu )Codice: Seleziona tutto
#!/bin/sh
# Slackbuild Creator v 0.3
# Written by Savino Pio Liguori aka jimmy_page_89
# Contact: jimmy_page_89 AT hotmail DOT it
# This script create a Slackbuild, following the standards of the
# Slacky.eu community ( http://www.slacky.eu )
# Actual standard: 13.37
# Redistribution and use of this script, with or without modification, is
# permitted provided that the following conditions are met:
#
# 1. Redistributions of this script must retain the above copyright
# notice, this list of conditions and the following disclaimer.
#
# THIS SOFTWARE IS PROVIDED BY THE AUTHOR ''AS IS'' AND ANY EXPRESS OR IMPLIED
# WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
# MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
# EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
# PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
# OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
# WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
# OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
# ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
WORKDIR=${WORKDIR:-$HOME}
FAVEDITOR=${FAVEDITOR:-vim}
# Set NO if you don't want to use Slacky.eu standard (At now only output directory tree)
SLACKYSTD=${SLACKYSTD:-YES}
set -e
# Defining commands "prototypes" (don't touch this)
COMMANDS="_intro
_define_name
_define_official_site
_define_author
_define_builder
_define_version
_set_build
_define_arch
_define_source_url
_set_tarball_name
_set_dir_name
_write_patch
_set_build_type
_write_special_op
_select_docs
_sharebin
_print_slackbuild
_slack_desc
_doinst
_outro"
# Defining functions
_set_tree()
{
# This section set AUTOMATICALLY where you want
# to put all your work.
#Don't edit this part!!!
if [ -d $WORKDIR/$NAME ]; then
rm -rf $WORKDIR/$NAME
fi
if [ "$SLACKYSTD" = "YES" ]; then
mkdir -p $WORKDIR/$NAME/$VER/src
EXPDIR=$WORKDIR/$NAME/$VER/src
else
EXPDIR=$WORKDIR
fi
}
_print_slackbuild()
{
_set_tree
_clscr
echo "Ok, all data insert."
echo ""
echo "Press Enter to create $NAME.Slackbuild in $EXPDIR"
echo ""
read
cat > $EXPDIR/$NAME.SlackBuild << EOF
#!/bin/sh
# Heavily based on the Slackware 13.37 SlackBuild (v1)
# Written by $AUTH ( $AUTHMAIL )
# Last build from $BUILDER ( $BUILDMAIL )
# Slackware build script for $NAME
# Official Site: $SITE
# Redistribution and use of this script, with or without modification, is
# permitted provided that the following conditions are met:
#
# 1. Redistributions of this script must retain the above copyright
# notice, this list of conditions and the following disclaimer.
#
# THIS SOFTWARE IS PROVIDED BY THE AUTHOR ''AS IS'' AND ANY EXPRESS OR IMPLIED
# WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
# MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
# EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
# PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
# OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
# WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
# OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
# ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
set -e
PKGNAME=$NAME
VERSION=\${VERSION:-$VER}
BUILD=\${BUILD:-$BUILD}
TAG=\${TAG:-sl}
ARCH=\${ARCH:-$ARCH}
SOURCE="$SRC"
TAR=$TAR
DIR=$DIR
# If EULA
if [ -e EULA.TXT ];then
more EULA.TXT
echo "Do you accept terms? (yes/[no])"
read ACCEPT
if [ "\$ACCEPT" != "yes" ];then
echo; echo "SlackBuild Aborted!!"
exit 1
fi
fi
# Does not touch following if not needed
CWD=\$(pwd)
TMP=\${TMP:-/tmp/buildpkgs/\$PKGNAME}
PKG=\$TMP/package-\$PKGNAME
OUTPUT=\${OUTPUT:-\$CWD}
TAR=\${TAR:-\$(basename \$SOURCE)}
DIR=\${DIR:-\$(echo "\$TAR"|sed -r 's/(\.tar|)(.gz|.bz2|)$//')}
if [ ! -e \$CWD/\$TAR ];then
wget \$SOURCE
fi
CHOST="i486"
if [ "\$ARCH" = "i486" ]; then
SLKCFLAGS="-O2 -march=i486 -mtune=i686"
LIBDIRSUFFIX=""
elif [ "\$ARCH" = "i586" ]; then
SLKCFLAGS="-O2 -march=i586 -mtune=i686"
LIBDIRSUFFIX=""
elif [ "\$ARCH" = "i686" ]; then
SLKCFLAGS="-O2 -march=i686 -mtune=i686"
LIBDIRSUFFIX=""
elif [ "\$ARCH" = "x86_64" ]; then
SLKCFLAGS="-O2 -fPIC"
LIBDIRSUFFIX="64"
CHOST="x86_64"
fi
rm -rf \$TMP
mkdir -p \$TMP \$PKG \$OUTPUT
cd \$TMP
tar xvf \$CWD/\$TAR
cd \$DIR
$PATCH
chown -R root:root .
chmod -R u+w,go+r-w,a-s .
$MAKE
$SPECIAL
mkdir -p \$PKG/usr/doc/\$PKGNAME-\$VERSION
cp -r \\
$DOC \\
\$PKG/usr/doc/\$PKGNAME-\$VERSION
cat \$CWD/\$PKGNAME.SlackBuild > \$PKG/usr/doc/\$PKGNAME-\$VERSION/\$PKGNAME.SlackBuild
cat \$CWD/slack-desc > \$PKG/usr/doc/\$PKGNAME-\$VERSION/slack-desc
if [ -d \$PKG/usr/man ]; then
( cd \$PKG/usr/man
find . -type f -exec gzip -9 {} \;
for i in \$( find . -type l ) ; do ln -s \$( readlink \$i ).gz \$i.gz ; rm \$i ; done
)
fi
( cd \$PKG
find . | xargs file | grep "executable" | grep ELF | cut -f 1 -d : | xargs -r strip --strip-unneeded 2> /dev/null || true
find . | xargs file | grep "shared object" | grep ELF | cut -f 1 -d : | xargs -r strip --strip-unneeded 2> /dev/null || true
find . | xargs file | grep "current ar archive" | cut -f 1 -d : | xargs -r strip --strip-unneeded 2> /dev/null || true
)
mkdir -p \$PKG/install
cat \$CWD/slack-desc > \$PKG/install/slack-desc
[ -e \$CWD/doinst.sh ] && cat \$CWD/doinst.sh > \$PKG/install/doinst.sh
cd \$PKG
chown -R root:root \$PKG
if [ -x "\$(which requiredbuilder 2>/dev/null)" ];then
requiredbuilder -y -v -s $SHAREBIN \$CWD \$PKG
fi
/sbin/makepkg -l y -c n \$OUTPUT/\$PKGNAME-\$VERSION-\$ARCH-\$BUILD\$TAG.\${PKGTYPE:-txz}
if [ "\$1" = "--cleanup" ]; then
rm -rf \$TMP
fi
EOF
}
_print_std_doinst()
{
cat > $EXPDIR/doinst.sh << EOF
config() {
NEW="\$1"
OLD="\$(dirname \$NEW)/\$(basename \$NEW .new)"
# If there's no config file by that name, mv it over:
if [ ! -r \$OLD ]; then
mv \$NEW \$OLD
elif [ "\$(cat \$OLD | md5sum)" = "\$(cat \$NEW | md5sum)" ]; then
# toss the redundant copy
rm \$NEW
fi
# Otherwise, we leave the .new copy for the admin to consider...
}
#if [ -e etc/rc.d/rc.script ]; then
# cp -a etc/rc.d/rc.script etc/rc.d/rc.script.new.incoming
# cat etc/rc.d/rc.script.new > etc/rc.d/rc.script.new.incoming
# mv etc/rc.d/rc.script.new.incoming etc/rc.d/rc.script.new
#fi
#config etc/rc.d/rc.script.new
#config etc/configfile.new
EOF
$FAVEDITOR $EXPDIR/doinst.sh
}
_print_slackdesc()
{
# This script was "inspired" from the original slack-desc script
# by naitso. You can find the original at this page:
# http://www.slacky.eu/wikislack/index.php?title=Crea_file_slack-desc
local COUNT=0
local R0
local R1
local R2
local R3
if [ -e $EXPDIR/slack-desc ]; then
rm $EXPDIR/slack-desc
fi
# First question
_clscr
echo "Write a very short package's description and press ENTER"
echo "(ex: Free FTP client)"
echo ""
read R1
# Second question
_clscr
echo "Write a package description and press ENTER"
echo "(ascii only no fancy character: a-z and - or _)"
echo ""
read R2
# Third question, only if you are NOT using Slacky.eu standard
if [ "$SLACKYSTD" = "NO" ]; then
_clscr
echo "Write package's homepage and press ENTER"
echo "(ex:http://www.example.org)"
echo ""
read R3
fi
# Build slack-desc
local NUM=0
local SPACE=$(echo "$NAME" | sed -e "s/./ /g")
local RULER="|----handy-ruler----"
local N_RULER=$(echo -n "$RULER" | wc -m)
local CHA=$(echo -n "$NAME" | wc -m)
# Set the max row for description
local MAX_ROW=9
# Limit the columns
local COL=$[77-$CHA]
if [ $CHA -gt "40" ]; then
echo "Name too long, please change it"
exit 1
fi
while [ $N_RULER -lt $[$COL+1] ]; do
local LINE=$LINE$(echo -n "-")
N_RULER=$[N_RULER+1]
done
# Slack-desc header
cat > $EXPDIR/slack-desc << EOF
# HOW TO EDIT THIS FILE:
# The "handy ruler" below makes it easier to edit a package description. Line
# up the first '|' above the ':' following the base package name, and the '|'
# on the right side marks the last column you can put a character in. You must
# make exactly 11 lines for the formatting to be correct. It's also customary
# to leave one space after the ':'.
$SPACE$RULER$LINE|
EOF
# limit description for slack-desc
local ROW=$(echo $R2 | fmt -w $COL | sed -e "s/^/$NAME: &/ " | wc -l)
if [ $ROW -ge "$MAX_ROW" ]; then
ROW=$MAX_ROW
fi
local MAX=$[$MAX_ROW-$ROW]
# Adding package-name and short description to file, (all in one line)
echo "$NAME ($R1)" | fmt -w $COL | sed -n -e "1,1s/^/$NAME: &/p " >> $EXPDIR/slack-desc
# Adding a empty row
echo $NAME: >> $EXPDIR/slack-desc
# Adding the description in max 7 rows
echo $R2 | fmt -w $COL | sed -n -e "1,7s/^/$NAME: &/p " >> $EXPDIR/slack-desc
if [ "$SLACKYSTD" = "NO" ]; then
# Adding a empty row before homepage
echo $NAME: >> $EXPDIR/slack-desc
# Adding homepage
echo "$NAME: ($R3)" >> $EXPDIR/slack-desc
fi
# If the rows are minus than 11, add the remaining (empty)
while [ $NUM -lt $MAX ]; do
echo "$NAME:" >> $EXPDIR/slack-desc
NUM=$[NUM+1]
done
}
_download()
{
_clscr
local URL
read -p "Insert your URL: " URL
wget $URL -O $EXPDIR/$(basename $URL)
}
_define_name()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
read -p "Package name: " NAME
echo ""
if [ -z "$NAME" ]; then
echo "Empty tag. Please rewrite."
read
else
echo "$NAME"
echo ""
read -p "OK, No(n) " END
fi
done
}
_define_official_site()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
read -p "Official site: " SITE
echo ""
if [ -z "$SITE" ]; then
echo "Empty tag. Please rewrite."
read
else
echo "$SITE"
echo ""
read -p "OK, No(n)" END
fi
done
}
_define_author()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
read -p "Author: " AUTH
echo ""
read -p "Contact: " AUTHMAIL
echo ""
if [ -z "$AUTH" -o -z "$AUTHMAIL" ]; then
echo "Empty tag(s). Please rewrite."
read
else
echo "$AUTH ( $AUTHMAIL )"
echo ""
read -p "OK, No(n)" END
fi
done
}
_define_builder()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
read -p "Last builder: " BUILDER
echo ""
read -p "Contact: " BUILDMAIL
echo ""
if [ -z "$BUILDER" -o -z "$BUILDMAIL" ]; then
echo "Empty tag(s). Please rewrite."
read
else
echo "$BUILDER ( $BUILDMAIL )"
echo ""
read -p "OK, No(n)" END
fi
done
}
_define_version()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
read -p "Package version: " VER
echo ""
if [ -z "$VER" ]; then
echo "Empty tag. Please rewrite."
read
else
echo "$VER"
echo ""
read -p "OK, No(n)" END
fi
done
}
_set_build()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
read -p "Package build (Enter if 1) :" BUILD
echo ""
if [ -z "$BUILD" ]; then
BUILD=1
fi
echo "$BUILD"
echo ""
read -p "OK, No(n)" END
done
}
_define_arch()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
echo "Please select architecture:"
echo " 1) i486"
echo " 2) i686"
echo " 3) x86_64"
echo " 4) noarch"
echo " 5) host (same as uname -m): "
echo ""
read ARCH
echo ""
if [ "$ARCH" = "1" ]; then
ARCH="i486"
elif [ "$ARCH" = "2" ]; then
ARCH="i686"
elif [ "$ARCH" = "3" ]; then
ARCH="x86_64"
elif [ "$ARCH" = "4" ]; then
ARCH="noarch"
elif [ "$ARCH" = "5" ]; then
ARCH=$(uname -m)
else
echo "Wrong option!"
echo "Please rewrite"
ARCH=""
read
fi
if [ ! -z "$ARCH" ]; then
echo "$ARCH"
echo ""
read -p "OK, No(n)" END
fi
done
}
_define_source_url()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
read -p "Source URL (Press Enter if not): " SRC
echo ""
if [ -z "$SRC" ]; then
echo "No download link"
else
echo "$SRC"
fi
echo ""
read -p "OK, No(n)" END
done
if [ ! -z "$SRC" ]; then
# Change the number version with the tag $VERSION
SRC=$(echo $SRC | sed -e 's/'$VER'/$VERSION/')
fi
}
_set_tarball_name()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
read -p "Tarball name (if not standard): " TAR
echo ""
if [ -z "$TAR" ]; then
END=""
else
echo "$TAR"
echo ""
read -p "OK, No(n)" END
fi
done
if [ ! -z "$TAR" ]; then
TAR=$(echo $TAR | sed -e 's/'$NAME'/$PKGNAME/' \
-e 's/'$VER'/$VERSION/')
fi
}
_set_dir_name()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
read -p "Source directory (if not standard): " DIR
echo ""
if [ -z "$DIR" ]; then
END=""
else
echo "$DIR"
echo ""
read -p "OK, No(n)" END
fi
if [ ! -z "$DIR" ]; then
DIR=$(echo $DIR | sed -e 's/'$NAME'/$PKGNAME/' \
-e 's/'$VER'/$VERSION/')
fi
done
}
_write_patch()
{
local END=n
if [ -e "$WORKDIR/patch.tmp" ]; then
rm $WORKDIR/patch.tmp
fi
while [ "$END" = "n" ]; do
_clscr
echo "Patch section"
echo "Now this script is going to open $FAVEDITOR where"
echo "you have to write the entire command of the patch(es)."
echo "Simply don't save if there aren't patches."
echo "(Don't forget the CWD variable!)"
echo ""
read
clear
$FAVEDITOR $EXPDIR/patch.tmp
_clscr
if [ -e "$WORKDIR/patch.tmp" ]; then
PATCH=$(cat $WORKDIR/patch.tmp)
echo "$PATCH"
fi
if [ ! -e "$WORKDIR/patch.tmp" -o -z "$PATCH" ]; then
echo "Nothing to patch"
fi
echo ""
read -p "OK, No(n)" END
done
if [ -e "$WORKDIR/patch.tmp" ]; then
rm $WORKDIR/patch.tmp
fi
}
_set_build_type()
{
local END=n
local BUTYPE
if [ -e $WORKDIR/build.tmp ]; then
rm $WORKDIR/build.tmp
fi
while [ "$END" = "n" ]; do
_clscr
echo "What type of build have this package?"
echo " 1) configure (DEFAULT)"
echo " 2) cmake"
echo " 3) python"
echo " 4) custom"
echo ""
read BUTYPE
if [ -z "$BUTYPE" ]; then
BUTYPE=1
fi
clear
case "$BUTYPE" in
1)
_std_conf
;;
2)
_cmake_conf
;;
3)
_py_conf
;;
4)
$FAVEDITOR $WORKDIR/build.tmp
esac
_clscr
if [ -e $WORKDIR/build.tmp ]; then
MAKE=$(cat $WORKDIR/build.tmp)
echo "$MAKE"
echo ""
fi
if [ ! -e "$WORKDIR/build.tmp" -o -z "$MAKE" ]; then
echo ""
echo "File not present. Please rewrite"
else
read -p "It's all ok? OK, No(n)" END
fi
if [ -e $WORKDIR/build.tmp ]; then
rm $WORKDIR/build.tmp
fi
done
}
_write_special_op()
{
local END=n
if [ -e "$WORKDIR/special.tmp" ]; then
rm $WORKDIR/special.tmp
fi
while [ "$END" = "n" ]; do
_clscr
echo ""
echo "Special operations section"
echo "Now this script is going to open $FAVEDITOR where"
echo "you have to write special operations."
echo "Simply don't save if there isn't nothing to do."
echo ""
read
clear
$FAVEDITOR $WORKDIR/special.tmp
_clscr
if [ -e "$WORKDIR/special.tmp" ]; then
SPECIAL=$(cat $WORKDIR/special.tmp)
echo "$SPECIAL"
fi
if [ ! -e "$WORKDIR/special.tmp" -o -z "$SPECIAL" ]; then
echo "Nothing to insert?"
fi
echo ""
read -p "OK, No(n)" END
done
if [ -e "$WORKDIR/special.tmp" ]; then
rm $WORKDIR/special.tmp
fi
}
_select_docs()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
read -p "Insert documentation file names: " DOC
echo ""
if [ -z "$DOC" ]; then
echo "Empty tag. Please rewrite."
read
else
echo "$DOC"
echo ""
read -p "OK, No(n)" END
fi
done
}
_sharebin()
{
local END=n
while [ "$END" = "n" ]; do
_clscr
read -p "Do you have some binaries in /usr/share? ok(y), NO " SHAREBIN
echo ""
if [ -z "$SHAREBIN" ]; then
echo "Nothing in /usr/share"
else
echo "Nothing in /usr/share"
SHAREBIN="-c -b"
fi
echo ""
read -p "OK, No(n)" END
done
}
_std_conf()
{
cat > $WORKDIR/build.tmp << EOF
CFLAGS="\$SLKCFLAGS" \\
CXXFLAGS="\$SLKCFLAGS" \\
./configure \\
--prefix=/usr \\
--libdir=/usr/lib\$LIBDIRSUFFIX \\
--sysconfdir=/etc \\
--localstatedir=/var \\
--mandir=/usr/man \\
--build=\$CHOST-slackware-linux
make
make install DESTDIR=\$PKG
EOF
$FAVEDITOR $WORKDIR/build.tmp
}
_cmake_conf()
{
cat > $WORKDIR/build.tmp << EOF
( mkdir -p build
cd build
cmake .. \
-DCMAKE_C_FLAGS:STRING="\$SLKCFLAGS" \\
-DCMAKE_CXX_FLAGS:STRING="\$SLKCFLAGS" \\
-DCMAKE_INSTALL_PREFIX=/usr \\
-DMAN_INSTALL_DIR=/usr/man \\
-DSYSCONF_INSTALL_DIR=/etc \\
-DLIB_SUFFIX=\${LIBDIRSUFFIX}
make
make install DESTDIR=\$PKG
)
EOF
$FAVEDITOR $WORKDIR/build.tmp
}
_py_conf()
{
cat > $WORKDIR/build.tmp << EOF
python setup.py install --root=\$PKG
EOF
$FAVEDITOR $WORKDIR/build.tmp
}
_slack_desc()
{
local OPT
_clscr
echo "What do you want to do with slack-desc?"
echo " 1) Create (DEFAULT)"
echo " 2) Download"
echo " 3) I do not want it"
echo ""
read OPT
if [ -z "$OPT" ]; then
OPT=1
fi
case "$OPT" in
1)
_print_slackdesc
;;
2)
_download
;;
3)
clear
echo ""
echo "Please supports fat pidgeons."
echo ""
read
;;
esac
}
_doinst()
{
local OPT
_clscr
echo "What do you want to do with doinst.sh?"
echo " 1) Create from Slacky Standard (DEFAULT)"
echo " 2) Create from scratch"
echo " 3) Download"
echo " 4) I don't need it."
echo ""
read OPT
if [ -z "$OPT" ]; then
OPT=1
fi
case "$OPT" in
1)
_print_std_doinst
;;
2)
$FAVEDITOR $EXPDIR/doinst.sh
;;
3)
_download
;;
4)
clear
echo ""
echo "Please supports fat pidgeons."
echo ""
read
;;
esac
}
_intro()
{
_clscr
echo "Press ENTER to start"
echo ""
read
}
_outro()
{
_clscr
echo "Ok, that's all folks. Thanks a lot for using Slackbuild Creator! ^TM"
read
}
_clscr()
{
clear
echo ""
echo "####################################################"
echo "# #"
echo "# SlackBuild Creator #"
echo "# by jimmy_page_89 #"
echo "# #"
echo "####################################################"
echo ""
}
# Now the real script starts. Radically simple!
for i in $COMMANDS; do
$i
done
exit 0Codice: Seleziona tutto
CHANGELOG
0.3
- Correct script header (thanks to brainvision)
- General fixed output
* Now is so coooool
- Inverted _doinst() and _slack_desc
- Changed command execution
* introduced COMMANDS
- Added _intro() and _outro() functions
- Added EXPDIR
* Set where you want to put slackbuilds
- In function _print_slackdesc()
* Removed clear
* Removed check of existing files, now it remove by default
* Main bugs fixed
* Removed variable FILE
* Fixed some local variables
* Added non-Slacky-standard support
* WARNING: consider ALL in TESTING
- In function _slack_desc()
* Set option 1 as default
* Set 3 to option NOT
* Changed variable DSK in OPT
- In function _doinst()
* Set option 1 as Slacky standard and made as default.
* Set option 2 to desc from scratch
* Set option 4 to NOT
- In function _download()
* Added EXPDIR
- In function _set_tarball_name()
* Out of testing the "sed" part
- In function _set_dir_name()
* Added "sed" correction part
- In function _set_build_type()
* Add first control, removing build.tmp if exists (TESTING)
* Set "configure" as default
- In function _write_special_op()
* Fixed first removing operation
- In function _set_build_type()
* Added second "if exists" control
- In function _write_special_op()
* Fixed control, file may not exists and you don't want it
- In function _print-slackbuild()
* moved _set_tree() inside
- Added some comments
0.2
- Changed default workdir
* Now is set to $HOME by default
- Fixed global variables
* Now you can determine they externally
- Inverted _build_type() and _special()
- Added SLACKYSTD
* Set NO if you don't want Slacky.eu standard
(WARNING: not implemented yet)
- In function _std_doinst()
* Renamed in _print_std_doinst
- In function _down_files()
* Renamed in _download (c'est plus facile)
* Fixed "mv" section to move every file you want
- In function _name()
* Renamed in _define_name()
- In function _official()
* Renamed in _define_official_site()
- In function _auth()
* Renamed in _define_author()
- In function _builder()
* Renamed in _define_builder()
- In function _arch()
* Renamed in _define_arch()
- In function _source()
* Renamed in _define_source_url()
- In function _tarball()
* Renamed in _set_tarball_name()
- In function _dir()
* Renamed in _set_dir_name()
- In function _patch()
* Renamed in _write_patch()
* Fix "rm" section
- In function _build_type()
* Renamed in _set_build_type()
- In function _special()
* Renamed in _write_special_op()
- In function _doc()
* Renamed in _select_docs
-
0.1
- First release
stavo per postare lo stesso identico problema!6C33C ha scritto:Ho provato copiarlo 2 votle ma la versione 0.3 mi da questo errore:
bash-4.1# ./SlackBuild_Creator
./SlackBuild_Creator: line 943: warning: here-document at line 91 delimited by end-of-file (wanted `EOF')
./SlackBuild_Creator: line 944: syntax error: unexpected end of file
slk_crt.tar.gz giusto.. risoltodanix ha scritto:se copiate dal forum fate attenzione che phpbb non abbia inserito degli spazi indesiderati..
Codice: Seleziona tutto
1011010 1100101 1110010 1101111 - 0100000 - 1010101 1101110 1101111E' una cosa che avrei voluto fare anche io, ma ho troppo limitate conoscenze di bash, sed & affiniZeroUno ha scritto:Tempo fa ne feci uno io (incompleto). Una caratteristica che mi piaceva: accettava in input solo l'url; il resto delle opzioni base se lo prendeva da solo (se l'url era standard; ma se ne potrebbe fare uno intelligente che si fa diversi controlli, lo scompatta pure e cerca da solo cose che possono essere utili o che fanno il pacchetto poco diverso)
) ora sono: scusa se rompo, comunque se hai intenzione di proseguire lo sviluppo ti conviene IMHO aggiornare di volta in volta il primo post e il relativo allegato, così se il thread si allunga non bisogna andare avanti nelle pagine per trovare le ultime versioni..jimmy_page_89 ha scritto:Avete ragione, risolvo subito
)Codice: Seleziona tutto
1011010 1100101 1110010 1101111 - 0100000 - 1010101 1101110 1101111