Moderatore: Staff
Codice: Seleziona tutto
pppd call gprsCodice: Seleziona tutto
# File:
# gprs
#
# Description:
# Serial cable, IrDA, Bluetooth and USB pppd options for GPRS phones.
# Keep pppd attached to the terminal:
# Comment this to get daemon mode pppd
nodetach
# Debug info from pppd:
# Comment this off, if you don't need more info
debug
# Show password in debug messages
show-password
# Connect script:
# scripts to initialize the GPRS modem and start the connection,
# wvdial command is for Orange SPV while other phones should work with chat
connect /etc/ppp/peers/gprs-connect-chat
#connect "/usr/bin/wvdial --chat --config /etc/ppp/peers/gprs-wvdial.conf
#radiolinja_usb_orange_spv"
# Disconnect script:
# AT commands used to 'hangup' the GPRS connection.
disconnect /etc/ppp/peers/gprs-disconnect-chat
# Serial device to which the GPRS phone is connected:
# /dev/ttyS0 for serial port (COM1 in Windows),
# /dev/ircomm0 for IrDA,
# /dev/ttyUB0 for Bluetooth (Bluez with rfcomm running) and
# /dev/ttyUSB0 for USB
#/dev/ttyS0 # serial port one
#/dev/ttyS1 # serial port two
#/dev/ircomm0 # IrDA serial port one
/dev/rfcomm0 # Bluetooth serial port one
#/dev/ttyUSB0 # USB serial device, for example Orange SPV
# Serial port line speed
115200 # fast enough
#57600 # perhaps usefull with IrDA
# Hardware flow control:
# Use hardware flow control with cable, Bluetooth and USB but not with IrDA.
crtscts # serial cable, Bluetooth and USB
#nocrtscts # IrDA
# Ignore carrier detect signal from the modem:
local
# IP addresses:
# - accept peers idea of our local address and set address peer as 10.0.0.1
# (any address would do, since IPCP gives 0.0.0.0 to it)
# - if you use the 10. network at home or something and pppd rejects it,
# change the address to something else
:10.0.0.1
# pppd must not propose any IP address to the peer!
noipdefault
# Accept peers idea of our local address
ipcp-accept-local
# Add the ppp interface as default route to the IP routing table
defaultroute
# DNS servers from the phone:
# some phones support this, some don't.
usepeerdns
# ppp compression:
# ppp compression may be used between the phone and the pppd, but the
# serial connection is usually not the bottleneck in GPRS, so the
# compression is useless (and with some phones need to disabled before
# the LCP negotiations succeed).
novj
nobsdcomp
novjccomp
nopcomp
noaccomp
# The phone is not required to authenticate:
noauth
# Username and password:
# If username and password are required by the APN, put here the username
# and put the username-password combination to the secrets file:
# /etc/ppp/pap-secrets for PAP and /etc/ppp/chap-secrets for CHAP
# authentication. See pppd man pages for details.
# Example, Radiolinja operator pap-secrets:
# "rlnet" * "internet" *
#user "rlnet"
#"" * ""
# Asyncmap:
# some phones may require this option.
#asyncmap 0xa0000
# No magic:
# some phones may require this option.
#nomagic
# Require PAP authentication:
# some phones may require this option.
#require-pap
# File:
# gprs
#
# Description:
# Serial cable, IrDA, Bluetooth and USB pppd options for GPRS phones.
# Keep pppd attached to the terminal:
# Comment this to get daemon mode pppd
nodetach
# Debug info from pppd:
# Comment this off, if you don't need more info
debug
# Show password in debug messages
show-password
# Connect script:
# scripts to initialize the GPRS modem and start the connection,
# wvdial command is for Orange SPV while other phones should work with chat
connect /etc/ppp/peers/gprs-connect-chat
#connect "/usr/bin/wvdial --chat --config /etc/ppp/peers/gprs-wvdial.conf
#radiolinja_usb_orange_spv"
# Disconnect script:
# AT commands used to 'hangup' the GPRS connection.
disconnect /etc/ppp/peers/gprs-disconnect-chat
# Serial device to which the GPRS phone is connected:
# /dev/ttyS0 for serial port (COM1 in Windows),
# /dev/ircomm0 for IrDA,
# /dev/ttyUB0 for Bluetooth (Bluez with rfcomm running) and
# /dev/ttyUSB0 for USB
#/dev/ttyS0 # serial port one
#/dev/ttyS1 # serial port two
#/dev/ircomm0 # IrDA serial port one
/dev/rfcomm0 # Bluetooth serial port one
#/dev/ttyUSB0 # USB serial device, for example Orange SPV
# Serial port line speed
115200 # fast enough
#57600 # perhaps usefull with IrDA
# Hardware flow control:
# Use hardware flow control with cable, Bluetooth and USB but not with IrDA.
crtscts # serial cable, Bluetooth and USB
#nocrtscts # IrDA
# Ignore carrier detect signal from the modem:
local
# IP addresses:
# - accept peers idea of our local address and set address peer as 10.0.0.1
# (any address would do, since IPCP gives 0.0.0.0 to it)
# - if you use the 10. network at home or something and pppd rejects it,
# change the address to something else
:10.0.0.1
# pppd must not propose any IP address to the peer!
noipdefault
# Accept peers idea of our local address
ipcp-accept-local
# Add the ppp interface as default route to the IP routing table
defaultroute
# DNS servers from the phone:
# some phones support this, some don't.
usepeerdns
# ppp compression:
# ppp compression may be used between the phone and the pppd, but the
# serial connection is usually not the bottleneck in GPRS, so the
# compression is useless (and with some phones need to disabled before
# the LCP negotiations succeed).
novj
nobsdcomp
novjccomp
nopcomp
noaccomp
# The phone is not required to authenticate:
noauth
# Username and password:
# If username and password are required by the APN, put here the username
# and put the username-password combination to the secrets file:
# /etc/ppp/pap-secrets for PAP and /etc/ppp/chap-secrets for CHAP
# authentication. See pppd man pages for details.
# Example, Radiolinja operator pap-secrets:
# "rlnet" * "internet" *
#user "rlnet"
#"" * ""
# Asyncmap:
# some phones may require this option.
#asyncmap 0xa0000
# No magic:
# some phones may require this option.
#nomagic
# Require PAP authentication:
# some phones may require this option.
#require-pap
Codice: Seleziona tutto
#!/bin/sh
#
# File:
# gprs-connect-chat
#
# Description:
# chat script to open Radiolinjas GPRS service with GPRS phones. If ppp
# negotiation stalls, try restarting the phone. To try with other GPRS
# operator setting, change the PDP contex setting. The settings work with
# most Ericsson models, but Nokia 8310 and 30 do not support QoS parameters
# with AT commands, so just delete those lines and it'll work.
#
# Set PDP context CID=1, protocol=IP, APN=internet:
AT+CGDCONT=1,"IP","internet.wind","",0,0
#
# Set CID=1 QoS requirements from the network, not supported by Nokia:
# AT+CGQREQ=1,0,0,0,0,0
#
# Set CID=1 minimum acceptable QoS parameters, not supported by Nokia:
# AT+CGQMIN=1,0,0,0,0,0
#
# 'Call' CID=1 (activate PDP context one, perform GPRS attach):
ATD*99#
#
# Some phones like the Orange SPV (yes, the Microsoft Smartphone) use this
# dial string to start GPRS connection:
# ATD*99#
#
# The actual chat script:
exec chat \
TIMEOUT 5 \
ECHO ON \
ABORT '\nBUSY\r' \
ABORT '\nERROR\r' \
ABORT '\nNO ANSWER\r' \
ABORT '\nNO CARRIER\r' \
ABORT '\nNO DIALTONE\r' \
ABORT '\nRINGING\r\n\r\nRINGING\r' \
'' \rAT \
TIMEOUT 12 \
SAY "Press CTRL-C to close the connection at any stage!" \
SAY "\ndefining PDP context...\n" \
OK ATH \
OK ATE1 \
OK 'AT+CGDCONT=1,"IP","internet","",0,0' \
OK ATD*99# \
TIMEOUT 22 \
SAY "\nwaiting for connect...\n" \
CONNECT "" \
SAY "\nConnected." \
SAY "\nIf the following ppp negotiations fail,\n" \
SAY "try restarting the phone.\n"
Codice: Seleziona tutto
defining PDP context...
OK
OK
OK
AT+CGDCONT=1,"IP","internet","",0,0
OK
waiting for connect...
ATD*99#
CONNECT
Connected.
If the following ppp negotiations fail,
try restarting the phone.
Serial connection established.
using channel 1
Using interface ppp0
Connect: ppp0 <--> /dev/rfcomm0
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x9c2203cd>]
rcvd [LCP ConfRej id=0x1 <magic 0x9c2203cd>]
sent [LCP ConfReq id=0x2 <asyncmap 0x0>]
rcvd [LCP ConfAck id=0x2 <asyncmap 0x0>]
rcvd [LCP ConfReq id=0x0 <auth pap> <mru 1500> <asyncmap 0xa0000>]
No auth is possible
sent [LCP ConfRej id=0x0 <auth pap>]
rcvd [LCP ConfReq id=0x1 <mru 1500> <asyncmap 0xa0000>]
sent [LCP ConfAck id=0x1 <mru 1500> <asyncmap 0xa0000>]
sent [LCP EchoReq id=0x0 magic=0x0]
kernel does not support PPP filtering
sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
rcvd [IPCP ConfReq id=0x0 <addr 10.6.6.6>]
sent [IPCP ConfNak id=0x0 <addr 10.0.0.1>]
rcvd [LCP EchoRep id=0x0 magic=0x0]
rcvd [LCP TermReq id=0x2]
LCP terminated by peer
sent [LCP TermAck id=0x2]
Connection terminated.
Sending break to the modem
PDP context detached
Serial link disconnected.
Modem hangup
Codice: Seleziona tutto
kernel does not support PPP filteringgraziesyaochan ha scritto:In Device Drivers -> Network Device Support -> PPP (point-to-point protocol) support
(se usi il 2.6)
Codice: Seleziona tutto
make mrproper