wifi help

[bloodlust]

si ora che hai aggiornato il kernel ricompila il driver per la scheda e installali.
poi facci sapere

[korkiras]

tutto ok grazieee ole ole
ora solo la devo configurare la mia wireless

che devo fare per configurare la wireless , che comando uso?

[korkiras]

iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

sit0 no wireless extensions.

ra0 RT2500 Wireless ESSID:"DLINK_WIRELESS" Nickname:"Hostname"
Mode:Managed Frequency=2.437 GHz Access Point: 00:17:9A:13:5D:60
Bit Rate=54 Mb/s Tx-Power:0 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality=82/100 Signal level=-64 dBm Noise level:-193 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon
manca la config per conetersi con router dove metto ip fissi mask ...
come si fa?

[bloodlust]

configura /etc/rc.d/rc.wireless.conf con i dati della tua rete wireless ed /etc/rc.d/rc.inet1.conf con le informazioni di rete (ip netmask gw ...)

[korkiras]

dopo che ho riaviato la wifi no funziona piu

non so come farla colleggare


# Config information for eth0:
IPADDR[0]="192.168.1.13"
NETMASK[0]="255.255.255.0"
USE_DHCP[0]=""
DHCP_HOSTNAME[0]=""

# Config information for eth1:
IPADDR[1]=""
NETMASK[1]=""
USE_DHCP[1]=""
DHCP_HOSTNAME[1]=""

# Config information for eth2:
IPADDR[2]=""
NETMASK[2]=""
USE_DHCP[2]=""
DHCP_HOSTNAME[2]=""

# Config information for eth3:
IPADDR[3]=""
NETMASK[3]=""
USE_DHCP[3]=""
DHCP_HOSTNAME[3]=""

# Default gateway IP address:
GATEWAY="192.168.1.1"

# Change this to "yes" for debugging output to stdout. Unfortunately,
# /sbin/hotplug seems to disable stdout so you'll only see debugging output
# when rc.inet1 is called directly.
DEBUG_ETH_UP="no"

## Example config information for wlan0. Uncomment the lines you need and fill
## in your info. (You may not need all of these for your wireless network)
#IFNAME[4]="wlan0"
#IPADDR[4]="192.168.1.14"
#NETMASK[4]="255.255.255.0"
#USE_DHCP[4]=""
#DHCP_HOSTNAME[4]="icculus-wireless"
#DHCP_KEEPRESOLV[4]=""
#DHCP_KEEPNTP[4]=""
#DHCP_KEEPGW[4]=""
#DHCP_IPADDR[4]=""
#WLAN_ESSID[4]=BARRIER05
#WLAN_MODE[4]=Managed
##WLAN_RATE[4]="54M auto"
##WLAN_CHANNEL[4]="auto"
##WLAN_KEY[4]="D5AD1F04ACF048EC2D0B1C80C7"
##WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP WPAPSK=7B1ABEEB5D197741923ED26727569C365E31212096A0EAFAD563B268BAD01CAF TxRate=0"
#WLAN_WPA[4]="wpa_supplicant"
#WLAN_WPADRIVER[4]="ndiswrapper"

## Some examples of additional network parameters that you can use.
## Config information for wlan0:
#IFNAME[4]="wlan0" # Use a different interface name nstead of
# the default 'eth4'
#HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address
#MTU[4]="" # The default MTU is 1500, but you might need
# 1360 when you use NAT'ed IPSec traffic.
#DHCP_KEEPRESOLV[4]="yes" # If you dont want /etc/resolv.conf overwritten
#DHCP_KEEPNTP[4]="yes" # If you don't want ntp.conf overwritten
#DHCP_KEEPGW[4]="yes" # If you don't want the DHCP server to change
# your default gateway
#DHCP_IPADDR[4]="" # Request a specific IP address from the DHCP
# server
#WLAN_ESSID[4]=DARKSTAR # Here, you can override _any_ parameter
# defined in rc.wireless.conf, by prepending
# 'WLAN_' to the parameter's name. Useful for
# those with multiple wireless interfaces.
#WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP WPAPSK=thekey TxRate=0"
# Some drivers require a private ioctl to be
# set through the iwpriv command. If more than
# one is required, you can place them in the
# IWPRIV parameter (space-separated, see the
# example).




e


Wireless LAN adapter configuration
#
# Theory of operation :
#
# The script attempts to match a block of settings to the specific wireless
# card inserted, the *first* block matching the card is used.
# The address format is "hwaddr", with * as a wildcard.
# 'hwaddr' is the unique MAC address identifier of the wireless card.
# The MAC address is usually printed on the card, or can be found via ifconfig.
# Some examples here use only half of the MAC address with a wildcard to
# match a whole family of cards...
#
# All the Wireless specific configuration is done through the Wireless
# Extensions, so we will just call 'iwconfig' with the right parameters
# defined below.
# Of course, you need to have iwconfig installled on your system.
# To download iwconfig, or for more info on Wireless Extensions :
# http://www.hpl.hp.com/personal/Jean_Tou ... Tools.html
#
# Note : you don't need to fill all parameters, leave them blank, in most
# cases the driver will initialise itself with sane defaults values or
# automatically figure out the value... And no drivers do support all
# possible settings...
#
# -- This is a modified '/etc/pcmcia/wireless.opts' script --
# -- I added sections for Prism/GT and Atheros based cards --
# -- (supported by the prism54 and madwifi drivers) --
# -- 16/sep/2004 * Eric Hameleers --
#

VERBOSE=1

case "$HWADDR" in

## NOTE : Comment out the following five lines to activate the samples below ...
## --------- START SECTION TO REMOVE -----------
## Pick up any Access Point, should work on most 802.11 cards
*)
INFO="Any ESSID"
ESSID="any"
;;
## ---------- END SECTION TO REMOVE ------------


# Here are a few examples with a few Wireless LANs supported...
# The matching is done on the first 3 bytes of the MAC address

# SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter
00:04:E2:*)
INFO="SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter"
# ESSID (extended network name) : My Network, any
ESSID="any"
# NWID/Domain (cell identifier) : 89AB, 100, off
NWID=""
# Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
MODE="Managed"
# Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
FREQ=""
CHANNEL="7"
# Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
SENS=""
# Bit rate : auto, 1M, 11M,54M
RATE="auto"
# Encryption key : 4567-89AB-CD, s:password
# Example for 40-bit encryption:
#KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
# Example for 104-bit encryption (aka 128-bit WEP):
#KEY="d5ad2f05abd048ecf10b1c80c7"
KEY=""
# RTS threshold : off, 500
RTS=""
# Fragmentation threshold : off, 1000
FRAG=""
# Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
IWCONFIG=""
# iwspy parameters : + 01:23:45:67:89:AB
IWSPY=""
# iwpriv parameters : set_port 2, set_histo 50 60
IWPRIV=""
;;

# Multiband Atheros based 802.11a/b/g universal NIC cards
00:05:4E:*)
INFO="Multiband Atheros based 802.11a/b/g universal NIC"
# ESSID (extended network name) : My Network, any
ESSID=""
# Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
MODE="Managed"
# Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
FREQ=""
CHANNEL="7"
# Bit rate : auto, 1M, 11M,54M
RATE="auto"
# Encryption key : 4567-89AB-CD, s:password
# Example for 40-bit encryption:
#KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
# Example for 104-bit encryption (aka 128-bit WEP):
#KEY="d5ad2f05abd048ecf10b1c80c7"
KEY=""
# Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
IWCONFIG=""
# iwspy parameters : + 01:23:45:67:89:AB
IWSPY=""
# iwpriv parameters : set_port 2, set_histo 50 60
IWPRIV=""
;;

# Lucent Wavelan IEEE (+ Orinoco, RoamAbout and ELSA)
# Note : wvlan_cs driver only, and version 1.0.4+ for encryption support
00:60:1D:*|00:02:2D:*)
INFO="Wavelan IEEE example (Lucent default settings)"
ESSID="Wavelan Network"
MODE="Managed"
#RATE="auto"
KEY="s:secu1"
# To set all four keys, use :
#KEY="s:secu1 [1] key s:secu2 [2] key s:secu3 [3] key s:secu4 [4] key [1]"
# For the RG 1000 Residential Gateway: The ESSID is the identifier on
# the unit, and the default key is the last 5 digits of the same.
#ESSID="084d70"
#KEY="s:84d70"
;;

# Cisco/Aironet 4800/3x0
# Note : MPL driver only (airo/airo_cs), version 1.3 or later
00:40:96:*|00:02:8A:*)
INFO="Cisco/Aironet example (Cisco default settings)"
ESSID="any"
# To set all four ESSID, use iwconfig v21 and the same trick as above
MODE="Managed"
#RATE="11M auto"
#KEY="d5ad2f05abd048ecf10b1c80c7"
KEY="off"
;;

# Samsung MagicLan (+ some other PrismII cards)
# Note : Samsung binary library driver, version 1.20 or later
00:00:F0:*|00:02:78:*)
INFO="Samsung MagicLan example (Samsung default settings)"
ESSID="any"
MODE="Managed"
CHANNEL="4"
RATE="auto"
#KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
#IWCONFIG="power on"
;;

# Raytheon Raylink/WebGear Aviator2.4
# Note : doesn't work yet, please use for debugging only
00:00:8F:*|00:00:F1:*)
INFO="Raylink/Aviator2.4 example (Aviator default ad-hoc setting)"
ESSID="ADHOC_ESSID"
MODE="Ad-Hoc"
RATE="auto"
IWPRIV="set_framing 1"
;;

# Old Lucent Wavelan
08:00:0E:*)
INFO="Wavelan example (Lucent default settings)"
NWID="0100"
MODE="Ad-Hoc"
FREQ="2.425G"
KEY="off"
;;

# Netwave (Xircom Netwave/Netwave Airsurfer)
00:80:C7:*)
INFO="Netwave example (Netwave default settings)"
NWID="100"
KEY="00"
;;

# Proxim RangeLan2/Symphony (what is the MAC address ???)
XX:XX:XX:*)
INFO="Proxim RangeLan2/Symphony example"
NWID="0"
MODE="Master"
CHANNEL="15"
IWPRIV="setsubchan 1"
;;

# No Wires Needed Swallow 550 and 1100 setting (what is the MAC address ???)
XX:XX:XX:*)
INFO="NWN Swallow example"
ESSID="session"
KEY="0000-0000-00 open"
;;

# Symbol Spectrum24 setting (what is the MAC address ???)
XX:XX:XX:*)
INFO="Symbol Spectrum24 example"
ESSID="Essid string"
;;

# Generic example (decribe all possible settings)
*)
INFO="Fill with your own settings..."
# ESSID (extended network name) : My Network, any
ESSID=""
# NWID/Domain (cell identifier) : 89AB, 100, off
NWID=""
# Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
MODE=""
# Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
FREQ=""
CHANNEL=""
# Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
SENS=""
# Bit rate : auto, 1M, 11M
RATE=""
# Encryption key : 4567-89AB-CD, s:password
KEY=""
# RTS threshold : off, 500
RTS=""
# Fragmentation threshold : off, 1000
FRAG=""
# Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
IWCONFIG=""
# iwspy parameters : + 01:23:45:67:89:AB
IWSPY=""
# iwpriv parameters : set_port 2, set_histo 50 60
IWPRIV=""
;;
esac






do io ip e wifi senza protezione
e non si accade la wifi dall avvio quindi solo da root dando racconfig2500