Problemi con /dev/sda1

slackboy · Messaggio da **slackboy** » ven 8 apr 2005, 9:40

SAlve ragazzi , utilizzo una slack 10.1 ed ho 2 kernel , u 2.4 e un 2.6.
 Nel 2.4 la directory /dev/sda1 et tutte le altre ci sono nel 2.6 non esiste nessun sda ,
 di conseguenza ho problemi a montare la pendrive .
 COme devo fare a ripristinare tutti gli sda??????

kyakan · Messaggio da **kyakan** » ven 8 apr 2005, 10:19

Non hai messo il supporto USB-Storage quando hai compilato il kernel probabilmente.
 
 /usr/src/linux# make menuconfig
 Device->USB Subbort->Mass Storage ... o giu di lì
 
 
 Se era gia dentro prova a caricare il modulo
 
 modprobe usb-storage
 
 Se lo carica prova a vedere se compaiono le sda quando inserisci il pendrive ...
 
 <TABLE BORDER=0 ALIGN=CENTER WIDTH=85%><TR><TD>Code:<HR></TD></TR><TR><TD><PRE> </PRE></TD></TR><TR><TD><HR></TD></TR></TABLE>

rob · Messaggio da **rob** » ven 8 apr 2005, 10:30

aggiungi nel kernel del 2.6 l´emulazione usb-scsi (non so se si chiami così, ma il concetto è quello :-] )
 praticamente nel 2.6 i dispositivi usb non vengono + emulati scsi, di conseguenza è cambiato l´inode che è diventato /dev/ubx... ripristinando l´emulazione, tornerai ad avere /dev/sdx
 
 ciao, rob

slackboy · Messaggio da **slackboy** » ven 8 apr 2005, 19:37

Ragazzi niente da fare , non riesco a montare la pen drive perhce non ho la cartalla /Dev/sda..... non sapete proprio come devo fare ??
 
 
 ps: nel kernel ci sono i moduli per usb storage anzi li ho caricati fissi neanche come moduli

gallows · Messaggio da **gallows** » ven 8 apr 2005, 19:43

fai una cosa, dai:
 
 %tail -F /var/log/messages
 
 inserisci la penna e posta qui il risultato.

j0ker · Messaggio da **j0ker** » ven 8 apr 2005, 20:57

Inserisci la pen-drive nel dispositivo e fai un bel "dmesg"...Verso la fine ti dovrebbe visualizzare il map del tuo device...Contralla un pò

slackboy · Messaggio da **slackboy** » sab 9 apr 2005, 14:20

allora per jocker :
 Il messagio che mi da è il seguete ....
 usb 1-3:new high speed USB device using_hcd and adress 2.
 
 per gallows:
 Il comando che mi hai dato non mi funziona.
 
 Ragazzi alllora qualcuno mi risolve questo problema????´

touchstyle · Messaggio da **touchstyle** » sab 9 apr 2005, 15:06

Postaci l´output dei comandi:
 
 ls -o /dev/sd*
 lsmod
 lspci
 
 Inoltre avvia la macchina con la penna inserita ed accesa (se necessario) e posta l´out di:
 
 dmesg
 
 Hai ricompilato il kernel correttamente?
 
 Ti consiglio di abbassare i toni e di terminare i post con un grazie (non per un fatto formale ma perchè stiamo cercando di aiutarti, anche non essendone obbligati).
 
 Ciao,
 Touch.

j0ker · Messaggio da **j0ker** » sab 9 apr 2005, 19:47

Nel dmesg non ricevi una riga del mapper sulla tua penna???Tipo che la mappa su sda,uba ecc... ???Fammi sapere CIAO

slackboy · Messaggio da **slackboy** » dom 10 apr 2005, 18:53

RAgazzi niente da fare , allora ls -o /dev/sd* non da nessun risultato e non ho trovato nessun messaggio relativo alla pend del dmesg ora vi allego il dmesg :
 
 Linux version 2.6.11.6 (root@1) (gcc version 3.3.4) #3 Wed Apr 6
 23:45:41 CEST 2005
 BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001f6e0000 (usable)
 BIOS-e820: 000000001f6e0000 - 000000001f6ea000 (ACPI data)
 BIOS-e820: 000000001f6ea000 - 000000001f700000 (ACPI NVS)
 BIOS-e820: 000000001f700000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
 BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
 502MB LOWMEM available.
 On node 0 totalpages: 128736
 DMA zone: 4096 pages, LIFO batch:1
 Normal zone: 124640 pages, LIFO batch:16
 HighMem zone: 0 pages, LIFO batch:1
 DMI present.
 ACPI: RSDP (v000 PTLTD ) @ 0x000f7530
 ACPI: RSDT (v001 Sony J0 0x20050225 PTL 0x00000000) @ 0x1f6e5a12
 ACPI: MADT (v001 Sony J0 0x20050225 PTL 0x0000005f) @ 0x1f6e9e78
 ACPI: FADT (v002 Sony J0 0x20050225 PTL 0x0000005f) @ 0x1f6e9ee0
 ACPI: BOOT (v001 Sony J0 0x20050225 PTL 0x00000001) @ 0x1f6e9fd8
 ACPI: MCFG (v001 Sony J0 0x20050225 PTL 0x0000005f) @ 0x1f6e9f9c
 ACPI: SSDT (v001 Sony J0 0x20050225 PTL 0x20030224) @ 0x1f6e62cf
 ACPI: SSDT (v001 Sony J0 0x20050225 PTL 0x20030224) @ 0x1f6e5e8a
 ACPI: SSDT (v001 Sony J0 0x20050225 PTL 0x20030224) @ 0x1f6e5c6f
 ACPI: SSDT (v001 Sony J0 0x20050225 PTL 0x20030224) @ 0x1f6e5a56
 ACPI: DSDT (v001 Sony J0 0x20050225 PTL 0x20030224) @ 0x00000000
 
 ACPI: PM-Timer IO Port: 0x1008
 ACPI: Local APIC address 0xfee00000
 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
 Processor #0 6:13 APIC version 20
 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
 ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
 ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
 IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
 ACPI: IRQ0 used by override.
 ACPI: IRQ2 used by override.
 ACPI: IRQ9 used by override.
 Enabling APIC mode: Flat. Using 1 I/O APICs
 Using ACPI (MADT) for SMP configuration information
 Allocating PCI resources starting at 20000000 (gap: 20000000:c0000000)
 Built 1 zonelists
 Kernel command line: BOOT_IMAGE=prova ro root=303
 __iounmap: bad address c00fffd9
 mapped APIC to ffffd000 (fee00000)
 mapped IOAPIC to ffffc000 (fec00000)
 Initializing CPU#0
 PID hash table entries: 2048 (order: 11, 32768 bytes)
 Detected 1596.979 MHz processor.
 Using pmtmr for high-res timesource
 Console: colour VGA+ 80x25
 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
 Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
 Memory: 505512k/514944k available (2927k kernel code, 8992k reserved, 1091k data, 288k init, 0k highmem)
 Checking if this processor honours the WP bit even in supervisor mode... Ok.
 Calibrating delay loop... 3145.72 BogoMIPS (lpj=1572864)
 Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
 CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
 CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
 CPU: L1 I cache: 32K, L1 D cache: 32K
 CPU: L2 cache: 2048K
 CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000
 Intel machine check architecture supported.
 Intel machine check reporting enabled on CPU#0.
 CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
 Enabling fast FPU save and restore... done.
 Enabling unmasked SIMD FPU exception support... done.
 Checking ´hlt´ instruction... OK.
 ENABLING IO-APIC IRQs
 ..TIMER: vector=0x31 pin1=2 pin2=-1
 NET: Registered protocol family 16
 EISA bus registered
 PCI: PCI BIOS revision 2.10 entry at 0xfd91f, last bus=8
 PCI: Using MMCONFIG
 mtrr: v2.0 (20020519)
 ACPI: Subsystem revision 20050211
 ACPI: Interpreter enabled
 ACPI: Using IOAPIC for interrupt routing
 ACPI: PCI Root Bridge [PCI0] (00:00)
 PCI: Probing PCI hardware (bus 00)
 PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
 PCI: Transparent bridge - 0000:00:1e.0
 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
 ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
 ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 *4 5 6 7 11 12 14 15)
 ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15)
 ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
 ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 *7 10 12 14 15)
 ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
 ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
 ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 7 11 12 14 15)
 ACPI: Embedded Controller [EC] (gpe 23)
 Linux Plug and Play Support v0.97 (c) Adam Belay
 pnp: PnP ACPI init
 pnp: PnP ACPI: found 8 devices
 SCSI subsystem initialized
 usbcore: registered new driver usbfs
 usbcore: registered new driver hub
 PCI: Using ACPI for IRQ routing
 ** PCI interrupts are no longer routed automatically. If this
 ** causes a device to stop working, it is probably because the
 ** driver failed to call pci_enable_device(). As a temporary
 ** workaround, the "pci=routeirq" argument restores the old
 ** behavior. If this argument makes the device work again,
 ** please email the output of "lspci" to <a href="mailto:bjorn.helgaas@hp.com" target="_new">bjorn.helgaas@hp.com</a>
 ** so I can fix the driver.
 NET: Registered protocol family 23
 Bluetooth: Core ver 2.7
 NET: Registered protocol family 31
 Bluetooth: HCI device and connection manager initialized
 Bluetooth: HCI socket layer initialized
 Simple Boot Flag at 0x36 set to 0x1
 IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
 VFS: Disk quotas dquot_6.5.1
 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
 NTFS driver 2.1.22 [Flags: R/W].
 Initializing Cryptographic API
 ACPI: AC Adapter [ADP1] (on-line)
 ACPI: Battery Slot [BAT0] (battery absent)
 ACPI: Video Device [NGFX] (multi-head: yes rom: no post: no)
 ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
 ACPI: CPU0 (power states: C1[C1] C2[C2])
 ACPI: Processor [CPU0] (supports 8 throttling states)
 isapnp: Scanning for PnP cards...
 isapnp: No Plug & Play device found
 HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
 N_HDLC line discipline registered.
 r3964: Philips r3964 Driver $Revision: 1.10 $
 Applicom driver: $Id: ac.c,v 1.30 2000/03/22 16:03:57 dwmw2 Exp $
 ac.o: No PCI boards found.
 ac.o: For an ISA board you must supply memory and irq parameters.
 Real Time Clock Driver v1.12
 Non-volatile memory driver v1.2
 i8xx TCO timer: heartbeat value must be 2<heartbeat<39, using 30
 i8xx TCO timer: initialized (0x1060). heartbeat=30 sec (nowayout=0)
 smapi::smapi_init, ERROR invalid usSmapiID
 mwave: tp3780i::tp3780I_InitializeBoardData: Error: SMAPI is not available on this machine
 mwave: mwavedd::mwave_init: Error: Failed to initialize board data
 mwave: mwavedd::mwave_init: Error: Failed to initialize
 i8042.c: Detected active multiplexing controller, rev 1.1.
 serio: i8042 AUX0 port at 0x60,0x64 irq 12
 serio: i8042 AUX1 port at 0x60,0x64 irq 12
 serio: i8042 AUX2 port at 0x60,0x64 irq 12
 serio: i8042 AUX3 port at 0x60,0x64 irq 12
 serio: i8042 KBD port at 0x60,0x64 irq 1
 Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
 io scheduler noop registered
 io scheduler anticipatory registered
 io scheduler deadline registered
 io scheduler cfq registered
 RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
 pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and <a href="mailto:petero2@telia.com" target="_new">petero2@telia.com</a>
 e100: Intel(R) PRO/100 Network Driver, 3.3.6-k2-NAPI
 e100: Copyright(c) 1999-2004 Intel Corporation
 ACPI: PCI interrupt 0000:06:08.0[A] -> GSI 20 (level, low) -> IRQ 20
 e100: eth0: e100_probe: addr 0xb0107000, irq 20, MAC addr 00:01:4A:19:39:09
 PPP generic driver version 2.4.2
 PPP Deflate Compression module registered
 PPP BSD Compression module registered
 NET: Registered protocol family 24
 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
 ICH6: IDE controller at PCI slot 0000:00:1f.1
 ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
 ICH6: chipset revision 4
 ICH6: not 100% native mode: will probe irqs later
 ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:DMA
 Probing IDE interface ide0...
 hda: HITACHI_DK23FA-60, ATA DISK drive
 hdb: MATSHITAUJ-831Da, ATAPI CD/DVD-ROM drive
 ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
 Probing IDE interface ide1...
 Probing IDE interface ide2...
 Probing IDE interface ide3...
 Probing IDE interface ide4...
 Probing IDE interface ide5...
 hda: max request size: 128KiB
 hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
 hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4
 ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
 ehci_hcd 0000:00:1d.7: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
 PCI: Setting latency timer of device 0000:00:1d.7 to 64
 ehci_hcd 0000:00:1d.7: irq 23, pci mem 0xb0004000
 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
 PCI: cache line size of 32 is not supported by device 0000:00:1d.7
 ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
 hub 1-0:1.0: USB hub found
 hub 1-0:1.0: 8 ports detected
 ohci_hcd: 2004 Nov 08 USB 1.1 ´Open´ Host Controller (OHCI) Driver (PCI)
 USB Universal Host Controller Interface driver v2.2
 AACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
 uhci_hcd 0000:00:1d.0: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
 PCI: Setting latency timer of device 0000:00:1d.0 to 64
 uhci_hcd 0000:00:1d.0: irq 23, io base 0x1820
 uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
 hub 2-0:1.0: USB hub found
 hub 2-0:1.0: 2 ports detected
 ACPI: PCI interrupt 0000:00:1d.1 -> GSI 19 (level, low) -> IRQ 19
 uhci_hcd 0000:00:1d.1: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
 PCI: Setting latency timer of device 0000:00:1d.1 to 64
 uhci_hcd 0000:00:1d.1: irq 19, io base 0x1840
 uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
 hub 3-0:1.0: USB hub found
 hub 3-0:1.0: 2 ports detected
 ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
 uhci_hcd 0000:00:1d.2: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
 PCI: Setting latency timer of device 0000:00:1d.2 to 64
 uhci_hcd 0000:00:1d.2: irq 18, io base 0x1860
 uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
 hub 4-0:1.0: USB hub found
 hub 4-0:1.0: 2 ports detected
 ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
 uhci_hcd 0000:00:1d.3: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
 PCI: Setting latency timer of device 0000:00:1d.3 to 64
 uhci_hcd 0000:00:1d.3: irq 16, io base 0x1880
 uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
 hub 5-0:1.0: USB hub found
 hub 5-0:1.0: 2 ports detected
 mice: PS/2 mouse device common for all mice
 input: AT Translated Set 2 keyboard on isa0060/serio0
 ALPS Touchpad (Glidepoint) detected
 Disabling hardware tapping
 input: AlpsPS/2 ALPS TouchPad on isa0060/serio4
 EISA: Probing bus 0 at eisa0
 Cannot allocate resource for EISA slot 1
 Cannot allocate resource for EISA slot 2
 EISA: Detected 0 cards.
 NET: Registered protocol family 2
 IP: routing cache hash table of 4096 buckets, 32Kbytes
 TCP established hash table entries: 16384 (order: 5, 131072 bytes)
 TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
 TCP: Hash tables configured (established 16384 bind 16384)
 Initializing IPsec netlink socket
 NET: Registered protocol family 1
 NET: Registered protocol family 17
 ACPI wakeup devices:
 PWRB USB1 USB2 USB3 USB4 USB7 LANC
 ACPI: (supports S0 S3 S4 S5)
 EXT2-fs warning (device hda3): ext2_fill_super: mounting ext3 filesystem as ext2
 VFS: Mounted root (ext2 filesystem) readonly.
 Freeing unused kernel memory: 288k freed
 Adding 1212896k swap on /dev/hda4. Priority:-1 extents:1
 Linux agpgart interface v0.100 (c) Dave Jones
 ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
 scsi0 : SCSI host adapter emulation for IDE ATAPI devices
 Vendor: MATSHITA Model: UJ-831Da Rev: 1.01
 Type: CD-ROM ANSI SCSI revision: 02
 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5
 sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
 Uniform CD-ROM driver Revision: 3.20
 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
 NTFS volume version 3.1.
 Linux Kernel Card Services
 options: [pci] [cardbus] [pm]
 Intel ISA PCIC probe: not found.
 Device ´i823650´ does not have a release() function, it is broken and must be fixed.
 Badness in device_release at drivers/base/core.c:85
 [<c022f2a8>] kobject_cleanup+0x98/0xa0
 [<c022f2b0>] kobject_release+0x0/0x10
 [<c022fd69>] kref_put+0x39/0xa0
 [<c022f2df>] kobject_put+0x1f/0x30
 [<c022f2df>] kobject_put+0x1f/0x30
 [<c022f2b0>] kobject_release+0x0/0x10
 [<e011c377>] init_i82365+0x1b7/0x1cd [i82365]
 [<c0134f86>] sys_init_module+0x186/0x240
 [<c01031af>] syscall_call+0x7/0xb
 Databook TCIC-2 PCMCIA probe: not found.
 PCI: Enabling device 0000:06:03.0 (0000 -> 0002)
 ACPI: PCI interrupt 0000:06:03.0[A] -> GSI 16 (level, low) -> IRQ 16
 Yenta: CardBus bridge found at 0000:06:03.0 [104d:818f]
 Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
 Socket status: 30000006
 cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
 cs: IO port probe 0x820-0x8ff: clean.
 cs: IO port probe 0x800-0x80f: clean.
 cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
 cs: IO port probe 0x100-0x3af: clean.
 cs: IO port probe 0xa00-0xaff: clean.
 ieee1394: Initialized config rom entry `ip1394´
 ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
 ACPI: PCI interrupt 0000:06:03.2[C] -> GSI 18 (level, low) -> IRQ 18
 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[b0104000-b01047ff] Max Packet=[2048]
 agpgart: Detected an Intel 915GM Chipset.
 agpgart: Maximum main memory to use for agp memory: 430M
 agpgart: Detected 7932K stolen memory.
 agpgart: AGP aperture is 256M @ 0xc0000000
 ieee1394: Host added: ID:BUS[0-00:1023] GUID[0800460301d17d1d]
 eth1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
 eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
 NET: Registered protocol family 10
 Disabled Privacy Extensions on device c04a5920(lo)
 IPv6 over IPv4 tunneling driver
 e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
 eth0: no IPv6 routers present
 mtrr: no more MTRRs available
 NTFS volume version 3.1.
 usb 1-5: new high speed USB device using ehci_hcd and address 2
 
 
 GRAZIE A TUTTI

gallows · Messaggio da **gallows** » dom 10 apr 2005, 18:59

il kernel l´hai compilato da te?
 hai incluso il supporto per le `mass storage` usb?

Messaggio da **twister** » dom 10 apr 2005, 19:01

prova con un bel
 modprobe usb-storage
 poi riattacca la penna e riposta un dmesg o al max un
 dmesg | grep usb
 Facci sapere
 byez!

ferenkileen · Messaggio da **ferenkileen** » dom 10 apr 2005, 19:20

spero di dire una cosa ovvia....
 ma fstab l´hai modificato?
 nel 2.4.x la pennetta funzia ancora?
 perchè non aggiungi a fstab
 /dev/uba1 (per kernel 2.6.x)
 /dev/sda1 (per kernel 2.4.x)
 
 You´re beautiful, you are, and you know it
 You´re wasted here, you´re a star in this small town of the hand-me-down
 You gotta go to the city!
 
 
 
 [ Questo Messaggio è stato Modificato da: ferenkileen il 10-04-2005 19:21 ]

tommyblue · Messaggio da **tommyblue** » dom 10 apr 2005, 19:22

nel kernel attiva (consiglio come modulo):
 device driver --> ATA/ATAPI/MFM/RLL Support --> SCSI Emulation support
 device driver --> SCSI device support --> SCSI disk support
 device driver --> USB support --> USB mass storage support
 
 devi anche attivare l´host usb del tuo pc, quindi uno tra:
 device driver --> USB support --> EHCI
 device driver --> USB support --> OHCI
 device driver --> USB support --> UHCI
 
 dovrebbe bastare, quando hai ricompilato e riavviato esegui:
 # tail -f /var/log/messages
 e solo dopo inserisci la penna usb, ti restituirà i messaggi necessari a capire in che device la troverai

Messaggio da **twister** » dom 10 apr 2005, 20:00

Se hai utilizzato il kernel di default, non hai bisogno di ricompilarlo, se usi udev con il 2.6 prova anche (se tutto quello detto prima non funziona) a fare
 cd /dev
 rm -R *
 udevstart
 e poi riprova ad attaccare la penna