[RISOLTO] Problema LSI53c1030 IBM eSERVER xSERIES 345

[j0kers]

Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)

E' il classico errore di quando non si compila staticamente o la partizione usata o il tipo di interfaccia del disco...In pratica devi compilare staticamente EXT3 o 4 a seconda del filesystem che usi, e Reiserfs staticamente, inoltre in Device Drivers nella sessione ATA/MFM ecc... devi compilare staticamente anche l'interfaccia del disco...

[n3tz666]

ho compilato staticamente Ext2 + Ext3 + Ext4 + reiserFs sbaglio a metterli tutti insieme ?

[n3tz666]

Ho riniziato da capo la compilazione riprendendomi il config di hugesmp.s
e ho iniziato modificando piano piano il kernel e compilando di volta in volta
sono arrivato al punto di avere il sistema con la specifica del mio processore, con i driver ethernet adeguati, e pare ancora non andare in kernel panic, ora l'unica cosa che mi lascia perplesso è la lentezza estenuante dei due dischi SCSI U320 posso allegare un dmesg se qualcuno sà darmi qualche consiglio i due dischi non sono in raid e sono su filesystem ext3

Codice: Seleziona tutto

mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptscsih: ioc0: attempting task abort! (sc=f6817e00)
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
scsi 0:0:0:0: CDB: cdb[0]=0x12: 12 00 00 00 a4 00
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x11010001): F/W: bug! MID not found
mptscsih: ioc0: task abort: SUCCESS (sc=f6817e00)
scsi target0:0:0: Domain Validation Disabing Information Units
mptbase: ioc0: LogInfo(0x11010001): F/W: bug! MID not found
scsi target0:0:0: mptspi: ioc0: mpt_config failed
scsi 0:0:0:0: Write Buffer failure 8000002
scsi target0:0:0: Domain Validation detected failure, dropping back
scsi 0:0:0:0: Write Buffer failure 8000002
scsi target0:0:0: Domain Validation detected failure, dropping back
scsi 0:0:0:0: Write Buffer failure 80000
scsi target0:0:0: Domain Validation detected failure, dropping back
mptscsih: ioc0: attempting task abort! (sc=f6817e00)
scsi 0:0:0:0: CDB: cdb[0]=0x3b: 3b 0a 00 00 00 00 00 01 fc 00
mptscsih: ioc0: WARNING - Issuing Reset from mptscsih_IssueTaskMgmt!!
mptbase: ioc0: Initiating recovery
mptscsih: ioc0: task abort: SUCCESS (sc=f6817e00)
scsi target0:0:0: Ending Domain Validation
scsi target0:0:0: asynchronous
sd 0:0:0:0: [sda] 71096640 512-byte logical blocks: (36.4 GB/33.9 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: c3 00 00 08
scsi 0:0:1:0: Direct-Access     IBM-ESXS MAP3367NC     FN B107 PQ: 0 ANSI: 3
scsi target0:0:1: Beginning Domain Validation
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
mptscsih: ioc0: attempting task abort! (sc=f73f0500)
scsi 0:0:1:0: CDB: cdb[0]=0x12: 12 00 00 00 a4 00
mptscsih: ioc0: task abort: SUCCESS (sc=f73f0500)
mptscsih: ioc0: attempting task abort! (sc=f73f0500)
scsi 0:0:1:0: CDB: cdb[0]=0x0: 00 00 00 00 00 00
mptscsih: ioc0: task abort: SUCCESS (sc=f73f0500)
mptscsih: ioc0: attempting target reset! (sc=f73f0500)
scsi 0:0:1:0: CDB: cdb[0]=0x12: 12 00 00 00 a4 00
mptscsih: ioc0: target reset: SUCCESS (sc=f73f0500)
mptscsih: ioc0: attempting task abort! (sc=f73f0500)
scsi 0:0:1:0: CDB: cdb[0]=0x12: 12 00 00 00 a4 00
mptscsih: ioc0: task abort: SUCCESS (sc=f73f0500)
mptscsih: ioc0: attempting task abort! (sc=f73f0500)
scsi 0:0:1:0: CDB: cdb[0]=0x0: 00 00 00 00 00 00
mptscsih: ioc0: task abort: SUCCESS (sc=f73f0500)
mptscsih: ioc0: attempting target reset! (sc=f73f0500)
scsi 0:0:1:0: CDB: cdb[0]=0x12: 12 00 00 00 a4 00
mptscsih: ioc0: target reset: SUCCESS (sc=f73f0500)
scsi target0:0:1: Domain Validation detected failure, dropping back
scsi target0:0:1: Domain Validation skipping write tests
scsi target0:0:1: Ending Domain Validation
scsi target0:0:1: asynchronous
sd 0:0:1:0: [sdb] 71096640 512-byte logical blocks: (36.4 GB/33.9 GiB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: c3 00 00 08
sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
mptspi 0000:08:07.1: PCI INT B -> GSI 28 (level, low) -> IRQ 28
mptbase: ioc1: Initiating bringup
 sdb:
ioc1: LSI53C1030 B2: Capabilities={Initiator}
scsi1 : ioc1: LSI53C1030 B2, FwRev=01032715h, Ports=1, MaxQ=222, IRQ=28
 sdb1
sd 0:0:1:0: [sdb] Attached SCSI disk
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: Invalid link context
ohci_hcd 0000:00:0f.2: PCI INT A: no GSI - using IRQ 11
ohci_hcd 0000:00:0f.2: OHCI Host Controller
ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0f.2: irq 11, io mem 0xfebfe000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32.8-smp ohci_hcd
usb usb1: SerialNumber: 0000:00:0f.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
sl811: driver sl811-hcd, 19 May 2005
r8a66597_hcd: driver r8a66597_hcd, 2009-05-26
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-onetouch
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x64,0x60 irq 1,12
PNP: PS/2 controller has invalid data port 0x64; using default 0x60
PNP: PS/2 controller has invalid command port 0x60; using default 0x64
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
cpuidle: using governor ladder
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
Freeing unused kernel memory: 404k freed
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, 242 bytes nvram
Linux agpgart interface v0.103
processor LNXCPU:00: registered as cooling_device0
processor LNXCPU:01: registered as cooling_device1
scb2_flash: flash probe failed!
piix4_smbus 0000:00:0f.0: SMBus Host Controller at 0x440, revision 0
Adding 1951888k swap on /dev/sda2.  Priority:-1 extents:1 across:1951888k
fuse init (API version 7.13)
EXT3 FS on sda1, internal journal
ppdev: user-space parallel port driver
lp: driver loaded but no devices found
NET: Registered protocol family 10

posto anche un lsmod e lspci -v

Codice: Seleziona tutto

Module                  Size  Used by
ipv6                  223088  12 
lp                      6908  0 
ppdev                   4882  0 
parport_pc             18155  0 
parport                25871  3 lp,ppdev,parport_pc
fuse                   50779  1 
i2c_piix4               7600  0 
cfi_probe               3623  0 
gen_probe               2065  1 cfi_probe
cfi_util                7690  1 cfi_probe
scb2_flash              2047  0 
mtd                    14433  1 scb2_flash
chipreg                 1254  2 cfi_probe,scb2_flash
processor              25580  0 
map_funcs               1210  1 scb2_flash
thermal                 9182  0 
sworks_agp              5170  0 
psmouse                37989  0 
thermal_sys            11694  2 processor,thermal
agpgart                23344  1 sworks_agp
rtc_cmos                7536  0 
rtc_core               11755  1 rtc_cmos
sg                     20441  0 
button                  3638  0 
serio_raw               3556  0 
hwmon                   1045  1 thermal_sys
rtc_lib                 1482  1 rtc_core
evdev                   6873  2 

Codice: Seleziona tutto

00:00.0 Host bridge: Broadcom CMIC-LE Host Bridge (GC-LE chipset) (rev 33)
	Flags: fast devsel
	Kernel modules: sworks-agp

00:00.1 Host bridge: Broadcom CMIC-LE Host Bridge (GC-LE chipset)
	Flags: fast devsel
	Kernel modules: sworks-agp

00:00.2 Host bridge: Broadcom CMIC-LE Host Bridge (GC-LE chipset)
	Flags: fast devsel
	Kernel modules: sworks-agp

00:06.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA controller])
	Subsystem: IBM Device 0240
	Flags: bus master, stepping, medium devsel, latency 64, IRQ 10
	Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
	I/O ports at 2400 [size=256]
	Memory at febff000 (32-bit, non-prefetchable) [size=4K]
	[virtual] Expansion ROM at 40000000 [disabled] [size=128K]
	Capabilities: [5c] Power Management version 2
	Kernel modules: atyfb

00:0f.0 Host bridge: Broadcom CSB5 South Bridge (rev 93)
	Subsystem: Broadcom CSB5 South Bridge
	Flags: bus master, medium devsel, latency 64
	Kernel driver in use: piix4_smbus
	Kernel modules: scb2_flash, i2c-piix4, sworks-agp

00:0f.1 IDE interface: Broadcom CSB5 IDE Controller (rev 93) (prog-if 82 [Master PriP])
	Subsystem: Broadcom CSB5 IDE Controller
	Flags: bus master, medium devsel, latency 64
	I/O ports at 01f0 [size=8]
	I/O ports at 03f4 [size=1]
	I/O ports at 0170 [size=8]
	I/O ports at 0374 [size=1]
	I/O ports at 0700 [size=16]
	Kernel driver in use: Serverworks_IDE

00:0f.2 USB Controller: Broadcom OSB4/CSB5 OHCI USB Controller (rev 05) (prog-if 10 [OHCI])
	Subsystem: Broadcom OSB4/CSB5 OHCI USB Controller
	Flags: bus master, medium devsel, latency 64, IRQ 11
	Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:0f.3 ISA bridge: Broadcom CSB5 LPC bridge
	Subsystem: Broadcom Dell PowerEdge 1650/1750
	Flags: bus master, medium devsel, latency 0

00:10.0 Host bridge: Broadcom CIOB-X2 PCI-X I/O Bridge (rev 05)
	Flags: 66MHz, medium devsel
	Capabilities: [60] PCI-X non-bridge device
	Kernel modules: sworks-agp

00:10.2 Host bridge: Broadcom CIOB-X2 PCI-X I/O Bridge (rev 05)
	Flags: 66MHz, medium devsel
	Capabilities: [60] PCI-X non-bridge device
	Kernel modules: sworks-agp

00:11.0 Host bridge: Broadcom CIOB-X2 PCI-X I/O Bridge (rev 05)
	Flags: 66MHz, medium devsel
	Capabilities: [60] PCI-X non-bridge device
	Kernel modules: sworks-agp

00:11.2 Host bridge: Broadcom CIOB-X2 PCI-X I/O Bridge (rev 05)
	Flags: 66MHz, medium devsel
	Capabilities: [60] PCI-X non-bridge device
	Kernel modules: sworks-agp

02:03.0 Ethernet controller: Intel Corporation 82544EI Gigabit Ethernet Controller (Copper) (rev 02)
	Subsystem: Intel Corporation PRO/1000 XT Server Adapter
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 20
	Memory at fbfe0000 (64-bit, non-prefetchable) [size=128K]
	Memory at fbfc0000 (64-bit, non-prefetchable) [size=128K]
	I/O ports at 2500 [size=32]
	[virtual] Expansion ROM at 40020000 [disabled] [size=128K]
	Capabilities: [dc] Power Management version 2
	Capabilities: [e4] PCI-X non-bridge device
	Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Kernel driver in use: e1000

06:08.0 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
	Subsystem: IBM PRO/1000 MT Dual Port Network Adapter
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 29
	Memory at f9fe0000 (64-bit, non-prefetchable) [size=128K]
	I/O ports at 2540 [size=64]
	Capabilities: [dc] Power Management version 2
	Capabilities: [e4] PCI-X non-bridge device
	Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Kernel driver in use: e1000

06:08.1 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
	Subsystem: IBM PRO/1000 MT Dual Port Network Adapter
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 30
	Memory at f9fc0000 (64-bit, non-prefetchable) [size=128K]
	I/O ports at 2580 [size=64]
	Capabilities: [dc] Power Management version 2
	Capabilities: [e4] PCI-X non-bridge device
	Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Kernel driver in use: e1000

08:07.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07)
	Subsystem: IBM Device 026c
	Flags: bus master, 66MHz, medium devsel, latency 72, IRQ 27
	I/O ports at 2600 [size=256]
	Memory at f7ff0000 (64-bit, non-prefetchable) [size=64K]
	Memory at f7fe0000 (64-bit, non-prefetchable) [size=64K]
	[virtual] Expansion ROM at 40100000 [disabled] [size=1M]
	Capabilities: [50] Power Management version 2
	Capabilities: [58] MSI: Enable- Count=1/1 Maskable- 64bit+
	Capabilities: [68] PCI-X non-bridge device
	Kernel driver in use: mptspi

08:07.1 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07)
	Subsystem: IBM Device 026c
	Flags: bus master, 66MHz, medium devsel, latency 72, IRQ 28
	I/O ports at 2700 [size=256]
	Memory at f7fd0000 (64-bit, non-prefetchable) [size=64K]
	Memory at f7fc0000 (64-bit, non-prefetchable) [size=64K]
	[virtual] Expansion ROM at 40200000 [disabled] [size=1M]
	Capabilities: [50] Power Management version 2
	Capabilities: [58] MSI: Enable- Count=1/1 Maskable- 64bit+
	Capabilities: [68] PCI-X non-bridge device
	Kernel driver in use: mptspi

Scusate l'immensa ignoranza

[j0kers]

Scusa puoi incollare il risultato di questo comando?

Codice: Seleziona tutto

lspci -v | grep driver

comunque sulla compilazione almeno all'inizio quando non sei convinto di una voce nel kernel al posto di ometterla compilala come M tanto più che occuparti un piccolo spazio in HD non fa niente...Poi mano mano quando il kernel è allegerito e funzionante come vuoi, allora procedi con l'eliminazione dei driver supplementari

[n3tz666]

ecco qui l'output rischiesto

root@darkstar:~# lspci -v | grep driver
Kernel driver in use: piix4_smbus
Kernel driver in use: Serverworks_IDE
Kernel driver in use: ohci_hcd
Kernel driver in use: e1000
Kernel driver in use: e1000
Kernel driver in use: e1000
Kernel driver in use: mptspi
Kernel driver in use: mptspi

[n3tz666]

Vi porto a conoscenza che a quanto pare questi errori in fase di boot

Codice: Seleziona tutto

mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptscsih: ioc0: attempting task abort! (sc=f6817e00)
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
scsi 0:0:0:0: CDB: cdb[0]=0x12: 12 00 00 00 a4 00
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem

sono dati da un'errore del disco o del controller scsi spostando uno dei due dischi in un'altro all'oggiamento del server quest'errore non c'è più bha misteri

[j0kers]

Infatti dal comando lspci non escono tutti i driver dell'hardware, manca l'audio il video ed altre cosucce....Hai omesso qualcosina...Controlla bene il tuo hardware

[n3tz666]

ehm....è un SERVER non ha audio per il video non mi serve non ho installato l' X

[j0kers]

Ah ok pensavo fosse un comune desktop...Hai dei dischi scsi? nella sessione Device Drivers > Scsi Device Support hai abilitato staticamente:

Scsi Disk, Scsi CDROM e Scsi Generic support?

[n3tz666]

si jokers, ho compilato statico quelle opzioni , ora ho provato a spostare il primo disco nel terzo bay ha 6 slot per dischi scsi di cui ho solo 2 dischi al momento scsi U320 a quanto pare il primo slot dà problemi ora ho spostato sul 2° e 3° slot e all'avvio del kernel (hugesmp.s al momento perchè ho appena reinstallato) non mi compaiono + queste scritte :

Codice: Seleziona tutto

mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem
mptbase: ioc0: LogInfo(0x110a0000): F/W: Device Problem

[j0kers]

Sembra che l'errore postato da te deriva da una scheda SCSI installata sul tuo PC o dalla periferica ottica...il DVDROM...Hai abilitato staticamente anche l'interfaccia del tuo CDROM/DVDROM???

Prova a installare staticamente il driver della scheda SCSI

[n3tz666]

A quanto sembra la mia scheda madre ha il controller scsi integrato sulla mainboard un LSI 53c1030, ho notato che questo chipset ha dei sui driver da integrare nel kernel devo provare

[j0kers]

Esattamente prova a compilarlo staticamente vedrai che non avrai problemi e l'errore sparirà...tienici aggiornati

Ciao

[n3tz666]

Grazie come rientro a casa proverò sicuramente speriamo che funziona grazie dell'aiuto dato

[j0kers]

Non c'è problema....Anzi facci sapere siamo a tua disposizione