[RISOLTO] Problema con eth0

yAri · Messaggio da **yAri** » mer 9 feb 2011, 20:22

Allora lanciando

modprobe atl1c

non succede nulla e non cambia nulla, neanche da errori.

Ecco l'altra parte che mi avevi chiesto:

Codice: Seleziona tutto

bash-4.1# lspci -v
00:00.0 Host bridge: Intel Corporation Pineview DMI Bridge (rev 02)
        Subsystem: ASUSTeK Computer Inc. Device 83ac
        Flags: bus master, fast devsel, latency 0
        Capabilities: [e0] Vendor Specific Information <?>
        Kernel driver in use: agpgart-intel
        Kernel modules: intel-agp

00:02.0 VGA compatible controller: Intel Corporation Pineview Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller])
        Subsystem: ASUSTeK Computer Inc. Device 8446
        Flags: bus master, fast devsel, latency 0, IRQ 29
        Memory at f5d00000 (32-bit, non-prefetchable) [size=512K]
        I/O ports at cc00 [size=8]
        Memory at b0000000 (32-bit, prefetchable) [size=256M]
        Memory at f5c00000 (32-bit, non-prefetchable) [size=1M]
        Expansion ROM at <unassigned> [disabled]
        Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
        Capabilities: [d0] Power Management version 2
        Kernel driver in use: i915
        Kernel modules: i915

00:02.1 Display controller: Intel Corporation Pineview Integrated Graphics Controller (rev 02)
        Subsystem: ASUSTeK Computer Inc. Device 8446
        Flags: bus master, fast devsel, latency 0
        Memory at f5d80000 (32-bit, non-prefetchable) [size=512K]
        Capabilities: [d0] Power Management version 2

00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
        Subsystem: ASUSTeK Computer Inc. Device 83ce
        Flags: bus master, fast devsel, latency 0, IRQ 30
        Memory at f5bf8000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [50] Power Management version 2
        Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
        Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [130] Root Complex Link <?>
        Kernel driver in use: HDA Intel
        Kernel modules: snd-hda-intel

00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: fa000000-fbffffff
        Prefetchable memory behind bridge: 00000000ce000000-00000000dfffffff
        Capabilities: [40] Express Root Port (Slot+), MSI 00
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
        Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 83ad
        Capabilities: [a0] Power Management version 2
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [180] Root Complex Link <?>
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
        I/O behind bridge: 00001000-00001fff
        Memory behind bridge: f6000000-f9ffffff
        Prefetchable memory behind bridge: 00000000c8000000-00000000cdffffff
        Capabilities: [40] Express Root Port (Slot+), MSI 00
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
        Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 83ad
        Capabilities: [a0] Power Management version 2
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [180] Root Complex Link <?>
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 02) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        I/O behind bridge: 0000d000-0000dfff
        Memory behind bridge: f5f00000-f5ffffff
        Prefetchable memory behind bridge: 00000000c0000000-00000000c01fffff
        Capabilities: [40] Express Root Port (Slot+), MSI 00
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
        Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 83ad
        Capabilities: [a0] Power Management version 2
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [180] Root Complex Link <?>
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 00002000-00002fff
        Memory behind bridge: f5e00000-f5efffff
        Prefetchable memory behind bridge: 00000000c0200000-00000000c03fffff
        Capabilities: [40] Express Root Port (Slot+), MSI 00
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
        Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 83ad
        Capabilities: [a0] Power Management version 2
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [180] Root Complex Link <?>
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
        Subsystem: ASUSTeK Computer Inc. Device 83ad
        Flags: bus master, medium devsel, latency 0, IRQ 23
        I/O ports at c400 [size=32]
        Kernel driver in use: uhci_hcd
        Kernel modules: uhci-hcd

00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
        Subsystem: ASUSTeK Computer Inc. Device 83ad
        Flags: bus master, medium devsel, latency 0, IRQ 19
        I/O ports at c480 [size=32]
        Kernel driver in use: uhci_hcd
        Kernel modules: uhci-hcd

00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
        Subsystem: ASUSTeK Computer Inc. Device 83ad
        Flags: bus master, medium devsel, latency 0, IRQ 18
        I/O ports at c800 [size=32]
        Kernel driver in use: uhci_hcd
        Kernel modules: uhci-hcd

00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
        Subsystem: ASUSTeK Computer Inc. Device 83ad
        Flags: bus master, medium devsel, latency 0, IRQ 16
        I/O ports at c880 [size=32]
        Kernel driver in use: uhci_hcd
        Kernel modules: uhci-hcd

00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
        Subsystem: ASUSTeK Computer Inc. Device 83ad
        Flags: bus master, medium devsel, latency 0, IRQ 23
        Memory at f5bf7c00 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
        Capabilities: [58] Debug port: BAR=1 offset=00a0
        Kernel driver in use: ehci_hcd
        Kernel modules: ehci-hcd

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
        Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device 83ad

00:1f.0 ISA bridge: Intel Corporation Tigerpoint LPC Controller (rev 02)
        Subsystem: ASUSTeK Computer Inc. Device 83ad
        Flags: bus master, medium devsel, latency 0
        Capabilities: [e0] Vendor Specific Information <?>

00:1f.2 SATA controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
        Subsystem: ASUSTeK Computer Inc. Device 83ad
        Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 28
        I/O ports at c080 [size=8]
        I/O ports at c000 [size=4]
        I/O ports at bc00 [size=8]
        I/O ports at b880 [size=4]
        I/O ports at b800 [size=32]
        Memory at f5bf7800 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
        Capabilities: [70] Power Management version 2
        Capabilities: [a8] SATA HBA <?>
        Kernel driver in use: ahci

00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
        Subsystem: ASUSTeK Computer Inc. Device 83ad
        Flags: medium devsel, IRQ 21
        I/O ports at 0400 [size=32]
        Kernel modules: i2c-i801

01:00.0 USB Controller: NEC Corporation Device 0194 (rev 03) (prog-if 30)
        Subsystem: ASUSTeK Computer Inc. Device 1019
        Flags: bus master, fast devsel, latency 0, IRQ 19
        Memory at f5efe000 (64-bit, non-prefetchable) [size=8K]
        Capabilities: [50] Power Management version 3
        Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
        Capabilities: [90] MSI-X: Enable- Count=8 Masked-
        Capabilities: [a0] Express Endpoint, MSI 00
        Capabilities: [100] Advanced Error Reporting
        Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
        Capabilities: [150] #18
        Kernel driver in use: xhci_hcd
        Kernel modules: xhci

02:00.0 Ethernet controller: Attansic Technology Corp. Device 2062 (rev c1)
        Subsystem: ASUSTeK Computer Inc. Device 8468
        Flags: bus master, fast devsel, latency 0, IRQ 10
        Memory at f5fc0000 (64-bit, non-prefetchable) [size=256K]
        I/O ports at dc00 [size=128]
        Capabilities: [40] Power Management version 3
        Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
        Capabilities: [58] Express Endpoint, MSI 00
        Capabilities: [6c] Vital Product Data
        Capabilities: [100] Advanced Error Reporting
        Capabilities: [180] Device Serial Number ff-7f-13-6c-20-cf-30-ff

03:00.0 Network controller: Broadcom Corporation Device 4727 (rev 01)
        Subsystem: Device 1a3b:2047
        Flags: bus master, fast devsel, latency 0, IRQ 15
        Memory at f9ffc000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [40] Power Management version 3
        Capabilities: [58] Vendor Specific Information <?>
        Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
        Capabilities: [d0] Express Endpoint, MSI 00
        Capabilities: [100] Advanced Error Reporting
        Capabilities: [13c] Virtual Channel <?>
        Capabilities: [160] Device Serial Number 00-00-60-ff-ff-2a-48-5d
        Capabilities: [16c] Power Budgeting <?>

05:00.0 VGA compatible controller: nVidia Corporation Device 0a76 (rev a2) (prog-if 00 [VGA controller])
        Subsystem: ASUSTeK Computer Inc. Device 8446
        Flags: fast devsel, IRQ 5
        Memory at fa000000 (32-bit, non-prefetchable) [disabled] [size=16M]
        Memory at d0000000 (64-bit, prefetchable) [disabled] [size=256M]
        Memory at ce000000 (64-bit, prefetchable) [disabled] [size=32M]
        I/O ports at ec00 [disabled] [size=128]
        Expansion ROM at fbf00000 [disabled] [size=512K]
        Capabilities: [60] Power Management version 3
        Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
        Capabilities: [78] Express Endpoint, MSI 00
        Capabilities: [b4] Vendor Specific Information <?>
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [128] Power Budgeting <?>
        Capabilities: [600] Vendor Specific Information <?>
        Kernel modules: nouveau, nvidiafb

Messaggio da **targzeta** » mer 9 feb 2011, 20:29

Ok, quindi il modulo c'è. Fai così:

Codice: Seleziona tutto

rmmod atl1c
dmesg -c
modprobe atl1c

e poi postaci l'output di:

Codice: Seleziona tutto

dmesg

Emanuele

yAri · Messaggio da **yAri** » mer 9 feb 2011, 21:06

Allora lanciando

Codice: Seleziona tutto

rmmod atl1c

dice che mi manca il modulo

Codice: Seleziona tutto

dmesg -c

mi da un mondo di cose e

Codice: Seleziona tutto

modprobe atl1c

non fa nulla.

lanciando poi

Codice: Seleziona tutto

dmesg

non appare nulla.

Messaggio da **targzeta** » mer 9 feb 2011, 21:14

Ok. Credo di aver risolto il dilemma. La Slackware 13.1 ha un kernel 2.6.33.4 ma il supporto per la tua scheda ethernet è incominciato con il kernel 2.6.34. Guarda qui:
http://git.kernel.org/?p=linux/kernel/g ... 578393cfe0
in particolare:

Codice: Seleziona tutto

atl1c AR8152(v2.0) 1969:2062 Fast Ethernet

Quindi come risolvi? Prova ad installare il kernel della current, questo non dovrebbe cambiare nulla ma in compenso hai i driver più aggiornati, anche se solo alle 2.6.35.10. Scaricati il pacchetto, ad esempio da qui:
ftp://ftp.lip6.fr/pub/linux/distributio ... ackware/a/
poi configuri LiLO in modo che possa farti il boot ANCHE con il nuovo kernel e riavvia utilizzando il 2.6.35.10. Questo dovrebbe bastare a farti apparire l'interfaccia con:

Codice: Seleziona tutto

ifconfig -a

Prova e facci sapere,
Emanuele

yAri · Messaggio da **yAri** » mer 9 feb 2011, 21:15

potresti spiegare per favore passo passo perchè credo che mi perderò..

Messaggio da **targzeta** » mer 9 feb 2011, 21:19

Che kernel usi? l'huge ho il generic?

Emanuele

yAri · Messaggio da **yAri** » mer 9 feb 2011, 21:46

hugesmp.s

Messaggio da **targzeta** » mer 9 feb 2011, 21:54

Ok per sicurezza, posta anche l'output di:

Codice: Seleziona tutto

grep -v '#' /etc/lilo.conf| uniq

Emanuele

yAri · Messaggio da **yAri** » mer 9 feb 2011, 22:46

si un attimo

yAri · Messaggio da **yAri** » mer 9 feb 2011, 23:03

L'output richiesto:

Codice: Seleziona tutto

# grep -v '#' /etc/lilo.conf| uniq
append=" vt.default_utf8=0"
boot = /dev/sda

  bitmap = /boot/slack.bmp
  bmp-colors = 255,0,255,0,255,0
  bmp-table = 60,6,1,16
  bmp-timer = 65,27,0,255

prompt
timeout = 1200
change-rules
  reset
vga = 773
other = /dev/sda1
  label = Windows
  table = /dev/sda
image = /boot/vmlinuz
  root = /dev/sda4
  label = Linux
  read-only

Messaggio da **targzeta** » mer 9 feb 2011, 23:17

Fai quanto segue:

scarica i due pacchetti:
ftp://ftp.lip6.fr/pub/linux/distributio ... i686-1.txz
ftp://ftp.lip6.fr/pub/linux/distributio ... i686-1.txz
Installa i pacchetti con 'installpkg'
Modifica il file /etc/lilo.conf come segue:
- al posto di 'image = /boot/vmlinuz' mettici 'image = /boot/vmlinuz-huge-2.6.33.4'
- inserisci quanto segue in fondo al file:
  Codice: Seleziona tutto
```
image = /boot/vmlinuz-huge-2.6.35.10
  root = /dev/sda4
  label = Linux-2.6.35.10
  read-only
```
esegui il comando 'lilo' e assicurati che non riporti errori
riavvia selezionando la voce 'Linux-2.6.35.10'

Facci sapere se riesci a vedere l'interfaccia eth0 con 'ifconfig -a',
Emanuele

yAri · Messaggio da **yAri** » gio 10 feb 2011, 15:56

Ti ringrazio per la tua pazienza e per il tuo aiuto che mi hai dato. Ho risolto il problema e ora sono collegato con il mio netbook.
Aggiungo solo che il file lilo.conf non era da modificare in quel modo visto che dava degli errori. L'ho lasciato così come era scritto prima, e mi ha comunque caricato il nuovo kernel. Posto comunque l'output richiesto:

Codice: Seleziona tutto

eth0      Link encap:Ethernet  HWaddr 20:cf:30:7f:13:6c  
          inet addr:10.81.51.18  Bcast:10.81.55.255  Mask:255.255.248.0
          inet6 addr: fe80::22cf:30ff:fe7f:136c/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1212 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1170 errors:0 dropped:0 overruns:0 carrier:1
          collisions:0 txqueuelen:1000 
          RX bytes:1265253 (1.2 MiB)  TX bytes:158215 (154.5 KiB)
          Interrupt:47 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:20 errors:0 dropped:0 overruns:0 frame:0
          TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:1000 (1000.0 B)  TX bytes:1000 (1000.0 B)

Già che ci sono ti volevo chiedere l'aiuto per l'audio che non funziona, se posso.. o devo creare un altro topic?

Messaggio da **targzeta** » gio 10 feb 2011, 16:26

Hai corso un rischio. Lasciando il lilo.conf inalterato non hai più la possibilità di usare il vecchio kernel, se qualcosa andava storto sarebbe stato un problema. Comunque meno male che tutto va bene.

Ti consiglio di seguire il consiglio di phobos per poter usare anche l'interfaccia wireless.

Per l'audio dovresti creare un altro topic.

Emanuele

yAri · Messaggio da **yAri** » gio 10 feb 2011, 16:34

si ma mi dava errore diceva che non esisteva "vmlinuz-huge-2.6.35.10" mi sono accorto che ha caricato quello nuovo dai cambiamenti nella fase di caricamento.
Grazie ancora.

Messaggio da **targzeta** » gio 10 feb 2011, 18:19

Da questo tuo post si evince che la modifica da fare al lilo.conf era:

al posto di 'image = /boot/vmlinuz' mettici 'image = /boot/vmlinuz-huge-2.6.33.4-smp'

inserisci quanto segue in fondo al file:

Codice: Seleziona tutto

image = /boot/vmlinuz-huge-2.6.35.10-smp
  root = /dev/sda4
  label = Linux-2.6.35.10
  read-only

Provalo, se funziona è meglio perché così hai sempre il vecchio 2.6.33.4 a disposizione tra le opzioni del lilo all'avvio.
Emanuele

slacky.eu

[RISOLTO] Problema con eth0

Re: Problema con eth0

Re: Problema con eth0

Re: Problema con eth0

Re: Problema con eth0

Re: Problema con eth0

Re: Problema con eth0

Re: Problema con eth0

Re: Problema con eth0

Re: Problema con eth0

Re: Problema con eth0

Re: Problema con eth0

Re: Problema con eth0

Re: [RISOLTO] Problema con eth0

Re: [RISOLTO] Problema con eth0

Re: [RISOLTO] Problema con eth0