La mia scheda è:
Codice: Seleziona tutto
# lspci | grep -i wlan
05:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)Codice: Seleziona tutto
# modprobe b43Codice: Seleziona tutto
# iwlist scan
lo Interface doesn't support scanning.
irda0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
Codice: Seleziona tutto
# ifconfig -a
irda0 Link encap:IrLAP HWaddr 00:00:00:00
NOARP MTU:2048 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:8
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:20 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1000 (1000.0 B) TX bytes:1000 (1000.0 B)
wlan0 Link encap:Ethernet HWaddr 00:1c:26:63:a2:9c
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Codice: Seleziona tutto
# ifconfig wlan0 up
SIOCSIFFLAGS: No such file or directory- /etc/wpa_supplicant.conf
Codice: Seleziona tutto
# See /usr/doc/wpa_supplicant-0.6.10/wpa_supplicant.conf.sample
# for many more options that you can use in this file.
# This line enables the use of wpa_cli which is used by rc.wireless
# if possible (to check for successful association)
ctrl_interface=/var/run/wpa_supplicant
# By default, only root (group 0) may use wpa_cli
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
#country=US
# WPA protected network, supply your own ESSID and WPAPSK here:
network={
scan_ssid=0
ssid="TISCALI"
proto=WPA RSN
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP WEP104 WEP40
psk=*******************************
priority=10
}
# Plaintext connection (no WPA, no IEEE 802.1X),
# nice for hotel/airport types of WiFi network.
network={
key_mgmt=NONE
priority=0
}- /etc/rc.d/rc.inet1.conf
Codice: Seleziona tutto
# Config information for eth0:
IPADDR[0]=""
NETMASK[0]=""
USE_DHCP[0]=""
DHCP_HOSTNAME[0]=""
# Config information for eth1:
IPADDR[1]=""
NETMASK[1]=""
USE_DHCP[1]=""
DHCP_HOSTNAME[1]=""
# Config information for eth2:
IPADDR[2]=""
NETMASK[2]=""
USE_DHCP[2]=""
DHCP_HOSTNAME[2]=""
# Config information for eth3:
IPADDR[3]=""
NETMASK[3]=""
USE_DHCP[3]=""
DHCP_HOSTNAME[3]=""
# Default gateway IP address:
GATEWAY=""
# Change this to "yes" for debugging output to stdout. Unfortunately,
# /sbin/hotplug seems to disable stdout so you'll only see debugging output
# when rc.inet1 is called directly.
DEBUG_ETH_UP="no"
## Example config information for wlan0. Uncomment the lines you need and fill
## in your data. (You may not need all of these for your wireless network)
IFNAME[4]="wlan0"
#IPADDR[4]=""
#NETMASK[4]=""
USE_DHCP[4]="yes"
#DHCP_HOSTNAME[4]="icculus-wireless"
DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"
#DHCP_KEEPGW[4]="yes"
#DHCP_IPADDR[4]=""
WLAN_ESSID[4]=TISCALI
WLAN_MODE[4]=Managed
#WLAN_RATE[4]="54M auto"
#WLAN_CHANNEL[4]="auto"
#WLAN_KEY[4]="D5A31F54ACF0487C2D0B1C10D2"
#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK="
WLAN_WPA[4]="wpa_supplicant"
WLAN_WPACONF[4]="/etc/wpa_supplicant.conf"
#WLAN_WPADRIVER[4]="wext"
#WLAN_WPAWAIT[4]=30
## Some examples of additional network parameters that you can use.
## Config information for wlan0:
#IFNAME[4]="wlan0" # Use a different interface name instead of
# the default 'eth4'
#IFNAME[4]="eth0:1" # Set up an IP alias.
#HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address
#MTU[4]="" # The default MTU is 1500, but you might need
# 1360 when you use NAT'ed IPSec traffic.
#DHCP_TIMEOUT[4]=15 # The default timeout for the DHCP client to
# wait for server resonse is 10 seconds, but
# you might want a shorter or longer wait.
#DHCP_KEEPRESOLV[4]="yes" # If you dont want /etc/resolv.conf overwritten
#DHCP_KEEPNTP[4]="yes" # If you don't want ntp.conf overwritten
#DHCP_KEEPGW[4]="yes" # If you don't want the DHCP server to change
# your default gateway
#DHCP_IPADDR[4]="" # Request a specific IP address from the DHCP
# server
#DHCP_DEBUG[4]="yes" # Make dhcpcd show verbose diagnostics
#DHCP_NOIPV4LL[4]="yes" # Do not assign an ipv4ll address when a DHCP
# server is not found (ipv4ll link-local
# adresses in the IP range 169.254.0.0/16 are
# also known as "zeroconf" addresses)
#WLAN_ESSID[4]=DARKSTAR # An example of how you can override _any_
# parameter defined in rc.wireless.conf, by
# prepending 'WLAN_' to the parameter's name.
# Useful with multiple wireless interfaces.
#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=thekey"
# Some drivers require a private ioctl to be
# set through the iwpriv command. If more than
# one is required, you can place them in the
# IWPRIV parameter (separated with the pipe (|)
# character, see the example).
#WLAN_WPA[4]="wpa_supplicant" # Run wpa_supplicant for WPA support
#WLAN_WPADRIVER[4]="ndiswrapper"# Tell wpa_supplicant to specifically use the
# ndiswrapper driver (if you leave this empty
# the 'wext' driver is used by default)
#WLAN_WPAWAIT[4]=30 # In case it takes long for the WPA association
# to finish, you can increase the wait time
# (defaults to 10 seconds)Codice: Seleziona tutto
# wpa_supplicant -d -c /etc/wpa_supplicant.conf -i wlan0
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
Initializing interface (2) 'wlan0'
SIOCSIFFLAGS: No such file or directory
Could not set interface 'wlan0' UP
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf flags 0x0
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:1c:26:63:a2:9c
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
WPS: UUID based on MAC address - hexdump(len=16): 71 ad 73 04 fd 55 52 43 8b 1e 9e 7a e1 e3 b4 46
WPS: Build Beacon and Probe Response IEs
WPS: * Version
WPS: * Wi-Fi Protected Setup State (0)
WPS: * Version
WPS: * Wi-Fi Protected Setup State (0)
WPS: * Response Type (2)
WPS: * UUID-E
WPS: * Manufacturer
WPS: * Model Name
WPS: * Model Number
WPS: * Serial Number
WPS: * Primary Device Type
WPS: * Device Name
WPS: * Config Methods (0)
WPS: * RF Bands (3)
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b1a len=40
l2_packet_receive - recvfrom: Network is down
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan to speed up initial association
ioctl[SIOCGIWSCAN]: Network is down
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
ioctl[SIOCSIWSCAN]: Network is down
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.
Setting scan request: 10 sec 0 usec
EAPOL: disable timer tick
Scan timeout - try to get results
ioctl[SIOCGIWSCAN]: Network is down
Failed to get scan results
Failed to get scan results - try scanning again
State: SCANNING -> INACTIVE
No enabled networks - do not scan
State: INACTIVE -> INACTIVE
E poi
Codice: Seleziona tutto
# /etc/rc.d/rc.inet1 restart
SIOCSIFFLAGS: No such file or directory
/etc/rc.d/rc.inet1: wlan0 information: 'Any ESSID'
Error for wireless request "Set Nickname" (8B1C) :
SET failed on device wlan0 ; Operation not supported.
SIOCSIFFLAGS: No such file or directory
Could not set interface 'wlan0' UP
SIOCSIFFLAGS: No such file or directory
Polling for DHCP server on interface wlan0:
dhcpcd: version 5.2.2 starting
dhcpcd: wlan0: up_interface: No such file or directory
dhcpcd: wlan0: waiting for carrier
dhcpcd: timed out
dhcpcd: allowing 8 seconds for IPv4LL timeout
dhcpcd: timed outCosa sbaglio? Suggerimenti?
Infatti vi sto scrivendo da slackware... 
Infatti ho eseguito anche la tua procedura ma non ha funzionato, forse perchè magari posso anche aver sbagliato io qualcosa... 
